Examen
Texas Wastewater Class A Exam Questions With Answers 100% Correct
- Cours
- Établissement
Texas Wastewater Class A Exam Questions With Answers 100% Correct
[Montrer plus]
3 revues
Par: big4john2005 • 4 mois de cela
Helpful
Par: fluxxcd • 7 mois de cela
Too many repeat questions..no questions on lagoons and acre feet..I just took test..
Par: jigalater • 11 mois de cela
Vendeur
S'abonner
Boffin
Avis reçus
Aperçu du contenu
Texas Wastewater Class A Exam Questionsand Answers 100% Correct
What is TCEQ doing to control "point source" pollution of the Texas waterways?
-Permitting of domestic wastewater plants
-Permitting of industrial wastewater plants
Describe proper design of force main wastewater lines. - Minimum two fps velocity
with the smallest pump operating alone. Minimum four inch diameter pipe with 150
psi rating.
What is Standard Dimension Ratio? - Ratio of outside pipe diameter (OD) to wall
thickness (PVC)
Describe proper design of gravity wastewater lines. - Designed to flow half full
,under normal conditions, at a minimum of two fps and a maximum of ten fps.
Manholes should have a minimum opening of? - 24 inches and be at least 4 feet wide.
pH meters should be calibrated how often? What standards should be used for
calibration purposes? - Daily with at least two buffers.
What is the standard chlorine residual and minimum contact time on Texas
wastewater permits? - a. 1.0 mg/L for a minimum 20 minutes detention time at peak
flow b. No chlorine residual needed if detention time is greater than 21 days
As the complexity of an organization increases, what management function becomes
most important? - Planning
What is the effective chlorine disinfecting agent? - Hypochlorous Acid (HOCl)
Does pH affect the chlorination process? Explain your answer. - When using free
chlorine the disinfectant is HOCl acid. As such it is much more effective at pH's below
7.0. Above 7.0 pH the acid begins to be neutralized.
What is the effluent chlorine residual in Texas that is standard on permits and the
minimum detention time? What is the maximum residual allowed? - Texas standard
is 1.0 mg/L for a minimum 20 minutes detention time at peak flow. Maximum
residual allowed is 4.0 mg/L.
A treatment plant has a clarifier that is 60 feet in diameter and is 10 feet deep. The
weir is 2 feet inside the outer clarifier wall. The flow is 1.0 MGD. The weir and
outflow channel is 3 feet deep. a. What is the detention time in hours? - Formula
, What activated process cannot nitrify in a single stage? - Contact Stabilization
What is the GPM output of a piston pump with an 8-inch diameter piston with a 10-
inch stroke operating at 50 strokes per minute? - Formula
A treatment plant has a clarifier that is 60 feet in diameter and is 10 feet deep. The
weir is 2 feet inside the outer clarifier wall. The flow is 1.0 MGD. The weir and
outflow channel is 3 feet deep.
a. What is the detention time in hours?
b. What is the surface loading in gal/ft2/day?
c. What is the weir loading in gal/linear ft/day? - Formulas
A primary clarifier has a flow of 3.0 MGD and has a diameter of 100 feet. It is 12 feet
deep and has 24 inches of freeboard. What is the detention time in hours? - Formulas
Anaerobic digester gas should contain? - 65-75% methane, 25-35% carbon dioxide
and 1-5% nitrogen.
An activated sludge plant has an average daily flow of 3.5 MG. The aeration tank
capacity is 1.2 MG with a MLSS concentration of 3200 mg/L. The clarifier has a
capacity of 400,000 gallons with a MLSS concentration of 6,000 mg/L. The wasting
rate is 40,000 gallons per day with a MLSS concentration of 8, 000 mg/L. The effluent
TSS is 18 mg/L. Assuming volatile concentrations of 70%, what is the MCRT and what
type of activated sludge plant should this be? - Formulas MCRT
What are some of the causes of filaments in the aeration basin? - a. low DO
b. low organic loading
c. septic wastes
d. nutrient deficiencies .
e. high sulfur content
Good sludge quality will have a predominance of what organisms in the MLSS? -
Ciliated protozoa
When an RBC is operating correctly, how will the slime appear on the media? - Grey
to brown 0.05 to 0.1 inches thick
According to design criteria, what are the minimum allowable diameters for a
manhole? - 24 inch opening and 48 inch inside diameter
What activated sludge process does not achieve complete nitrification? - Contact
Stabilization
In the selection of forced main wastewater piping, what is the minimum working
pressure? - 150 psi
Les avantages d'acheter des résumés chez Stuvia:
Qualité garantie par les avis des clients
Les clients de Stuvia ont évalués plus de 700 000 résumés. C'est comme ça que vous savez que vous achetez les meilleurs documents.
L’achat facile et rapide
Vous pouvez payer rapidement avec iDeal, carte de crédit ou Stuvia-crédit pour les résumés. Il n'y a pas d'adhésion nécessaire.
Focus sur l’essentiel
Vos camarades écrivent eux-mêmes les notes d’étude, c’est pourquoi les documents sont toujours fiables et à jour. Cela garantit que vous arrivez rapidement au coeur du matériel.
Foire aux questions
Qu'est-ce que j'obtiens en achetant ce document ?
Vous obtenez un PDF, disponible immédiatement après votre achat. Le document acheté est accessible à tout moment, n'importe où et indéfiniment via votre profil.
Garantie de remboursement : comment ça marche ?
Notre garantie de satisfaction garantit que vous trouverez toujours un document d'étude qui vous convient. Vous remplissez un formulaire et notre équipe du service client s'occupe du reste.
Auprès de qui est-ce que j'achète ce résumé ?
Stuvia est une place de marché. Alors, vous n'achetez donc pas ce document chez nous, mais auprès du vendeur Boffin. Stuvia facilite les paiements au vendeur.
Est-ce que j'aurai un abonnement?
Non, vous n'achetez ce résumé que pour €17,55. Vous n'êtes lié à rien après votre achat.
Peut-on faire confiance à Stuvia ?
4.6 étoiles sur Google & Trustpilot (+1000 avis)
78140 résumés ont été vendus ces 30 derniers jours
Fondée en 2010, la référence pour acheter des résumés depuis déjà 14 ans