Garantie de satisfaction à 100% Disponible immédiatement après paiement En ligne et en PDF Tu n'es attaché à rien
logo-home
Recherché précédemment par vous
Recherché précédemment par vous
logo
CNST 210 || Questions and 100% Accurate Answers. €12,30
Ajouter au panier
Accédez rapidement à
Aperçu
  2.  
  3. CNST 210
  4.  
  5. CNST 210

Examen

CNST 210 || Questions and 100% Accurate Answers.
 0 fois vendu
  • Cours
  • CNST 210
  • Établissement
  • CNST 210

These tapered steel tools are used by ironworkers to align and hold steel pieces together during the steel erection process. correct answers Drift pins Methods of fireproofing steel columns include all of the following except correct answers encasement in OSB or MDF. Bolt holes in steel membe...

[Montrer plus]

Aperçu 3 sur 16  pages

Infos sur le Document

  • 4 août 2024
  • 16
  • 2024/2025
  • Examen
  • Questions et réponses

Sujets

  • these tapered steel tools are used by ironworkers

École, étude et sujet

  • CNST 210
  • CNST 210

Vendeur

avatar-seller
FullyFocus

Avis reçus

Aperçu du contenu

CNST 210 || Questions and 100% Accurate Answers.
These tapered steel tools are used by ironworkers to align and hold steel pieces together during
the steel erection process. correct answers Drift pins

Methods of fireproofing steel columns include all of the following except correct answers
encasement in OSB or MDF.

Bolt holes in steel members can only be drilled per the AISC code. They can not be punched.
correct answers False

What are the two primary methods for connecting structural steel today? correct answers Bolting
and Welding

The three main ASTM Bolt types are? correct answers A307, A325, A490

The two basic bolted joint types are? correct answers Bearing and Slip-critical

These are all ways to tighten a slip-critical connection except correct answers Knuckle tight

The most commonly made type of weld is? correct answers Fillet

Welding positions include all of the following except? correct answers Sideways

The name of the construction workers trained in the erection of steel is correct answers
Ironworkers

The weight of one 30 ft long W16 x 26 section is correct answers 780 lbs

You have to transport a load of W16 x 26 wide flange sections from your fabrication shop to the
construction jobsite. The length of the sections is 30'. The maximum allowable load on the
tridem axle flatbed trailer that will be used to haul the steel is 42,500 lbs. How many W16 x 26
sections can you fit on the trailer? correct answers 54

You have to transport a load of L6 x 6 x ½ angle sections from your fabrication shop to the
construction jobsite. The length of sections is 20'. The maximum allowable load on the tridem
axle flatbed trailer that will be used to haul the steel is 42,500 lbs. How many L6 x 6 x ½ angle
sections can you fit on the trailer? correct answers 108

Go to https://www.aisc.org/steel-solutions-center/. Click the blue box that says "View Technical
Solutions" and then under "Frequently Asked Questions" select "6. Bolting" to find the answer to
the following question: Information that must be included in the purchase order for high-strength
bolts includes all of the following except correct answers For projects requiring slip-critical
connections, that the lubricated bolt, nut and washer be pre-assembled to ensure proper fit of the
bolt and nut and that the lot be tested for strength prior to shipment to the purchaser to meet the
requirements of the 2004 RCSC Specification Table 4.

,Go to https://www.aisc.org/steel-solutions-center/. Click the blue box that says "View Technical
Solutions" and then "Frequently Asked Questions". Answer the following question:
What minimum stick-through is required for high-strength bolts? (hint: See "other general
information") correct answers None

A British UB 305 x 165 x 40 (Universal Beam) has a unit mass of 40.3 kg/m. How many 9 meter
long UB 305 x 165 x 40 sections can you fit on a flat bed trailer that has a capacity of 20,000 kg?
correct answers 55

Bolts and nuts should be cleaned of all grease, wax or other lubricant prior to installation (if you
are not sure, Ask AISC). correct answers False

AISC recommends that owners ensure that their steel fabricators use this certification program.
correct answers AISC Quality Certification Program

A tack weld is correct answers a temporary weld used to hold parts in place while more
extensive, final welds are made

Just under the layer of "dead" bark on a tree is a layer of "living" bark. Within the "living" bark
is this thin layer that creates new bark cells toward the outside of the trunk and new wood cells
toward the inside. correct answers Cambium

Wood cells are structured of tough cellulose (a natural polymer) and are bound together by a
softer cementing substance called correct answers lignin

This type of sawing requires the least repositioning of the log during sawing and produces the
maximum yield of useful wood pieces. correct answers plainsawn

The actual dimensions of a 2 x 6 are correct answers 1 ½" x 5 ½"

Lumber is usually seasoned before it is surfaced, which allows the planning process to remove
some of the distortions that occur during seasoning. correct answers True

The compressive strength (stress parallel to grain) of southern pine, select structural grade is
correct answers 1900 psi (13 MPa).

Wood produced in very thin sheets is called veneer. The log from which veneer is taken is called
correct answers flitch

A 2 x 4 that is 16 feet long contains this many board feet. correct answers 10.67

Cross-Laminated Timber (CLT) correct answers These are structural panels laminated from solid
lumber, with the orientation of members alternating between layers. Finished panels range in size
from 2 to 10 feet in width, 40 to 60 feet in length and up to 20 inches in thickness.

, Glulam (GLT) correct answers Large wood structural members produced by gluing together
many smaller pieces of dimension lumber.

I-Joists correct answers These wood products are used for framing of both roofs and floors and
consist of a top and bottom flange made from solid lumber, LVL, or LSL, and webs made from
plywood or OSB.

Laminated Strand Lumber (LSL) correct answers Made from shredded wood strands, coated
with adhesive, pressed into a rectangular cross section, and cured under heat and pressure.

Laminated Veneer Lumber (LVL) correct answers Made from thin wood veneer sheets, as wide
as the member is deep, that are glued and laminated into thicker members.

Medium-density overlay (MDO) correct answers Plywood finished with a resin-treated overlay
for use where an especially smooth and durable surface is required.

Oriented Strand Board correct answers Made of long shreds (strands) of wood compressed and
glued into three to five layers making this structural wood product the strongest and stiffest type
of non-veneered panel.

Wood-Plastic Composites correct answers These products are made from blends of plastic with
wood or agricultural fibers, usually in roughly equal proportions and used most often for exterior
decking, railing systems, and finish trim. They do tend to expand and contract more with
temperature changes and have limited structural applications.

Structural Insulated Panels (SIPs) correct answers These wood products consist of wood panels
adhered to a stiff plastic foam core and are a popular choice for the construction of highly
energy-efficient homes and small buildings.

Trusses correct answers These triangular-based structural units can be used for both roof and
floor construction and are typically manufactured in small, highly efficient plants.

When wood is seasoned, moisture is removed. The moisture condition at which all free water has
evaporated is termed the fiber saturation point (FSP) and the average moisture content at this
point is around correct answers 30 percent.

Nails are correct answers sharp-pointed metal pins that are driven into wood with a hammer or a
mechanical gun.

Wood adhesives are used less on the construction site, where it is more difficult to clamp and
hold glued joints and to maintain controlled temperatures and humidity until the adhesive has
cured. correct answers True

Wood adhesives are used less on the construction site, where it is more difficult to clamp and
hold glued joints and to maintain controlled temperatures and humidity until the adhesive has
cured. correct answers True

Les avantages d'acheter des résumés chez Stuvia:

Qualité garantie par les avis des clients

Qualité garantie par les avis des clients

Les clients de Stuvia ont évalués plus de 700 000 résumés. C'est comme ça que vous savez que vous achetez les meilleurs documents.

L’achat facile et rapide

L’achat facile et rapide

Vous pouvez payer rapidement avec iDeal, carte de crédit ou Stuvia-crédit pour les résumés. Il n'y a pas d'adhésion nécessaire.

Focus sur l’essentiel

Focus sur l’essentiel

Vos camarades écrivent eux-mêmes les notes d’étude, c’est pourquoi les documents sont toujours fiables et à jour. Cela garantit que vous arrivez rapidement au coeur du matériel.

Foire aux questions

Qu'est-ce que j'obtiens en achetant ce document ?

Vous obtenez un PDF, disponible immédiatement après votre achat. Le document acheté est accessible à tout moment, n'importe où et indéfiniment via votre profil.

Garantie de remboursement : comment ça marche ?

Notre garantie de satisfaction garantit que vous trouverez toujours un document d'étude qui vous convient. Vous remplissez un formulaire et notre équipe du service client s'occupe du reste.

Auprès de qui est-ce que j'achète ce résumé ?

Stuvia est une place de marché. Alors, vous n'achetez donc pas ce document chez nous, mais auprès du vendeur FullyFocus. Stuvia facilite les paiements au vendeur.

Est-ce que j'aurai un abonnement?

Non, vous n'achetez ce résumé que pour €12,30. Vous n'êtes lié à rien après votre achat.

Peut-on faire confiance à Stuvia ?

4.6 étoiles sur Google & Trustpilot (+1000 avis)

69252 résumés ont été vendus ces 30 derniers jours

Fondée en 2010, la référence pour acheter des résumés depuis déjà 15 ans

Commencez à vendre!
€12,30
  • (0)
Ajouter au panier
Ajouté