Driver Operator Mobile Water Supply Exam Questions And Answers
3 vues 0 achat
Cours
Mobile Water Supply
Établissement
Mobile Water Supply
Driver Operator Mobile Water Supply Exam Questions And Answers
Identify FIVE requirements for a MWS apparatus that can be found in NFPA 1901 - ANS 1. An MWS apparatus equipped with a fire pump must have a tank to pump line at least two inches in diameter and be capable of supplying the pump wit...
Identify FIVE requirements for a MWS apparatus that can be found in NFPA 1901 - ANS 1. An MWS
apparatus equipped with a fire pump must have a tank to pump line at least two inches in diameter and be
capable of supplying the pump with 500 GPM until at least 80% of the tank is emptied.
2. An MWS apparatus must be equipped with at least one external fill connection connected into the tank
K
that allows the tank to be filled at a minimum rate of 1000 GPM.
3. The external fill connection should be equipped with a valve, strainer, and a 30 degree elbow.
C
4.Valves that are three inches or larger must be of the slow closing design.
LO
5. An MWS apparatus must have at least three large tank discharges capable of discharging 90% of the
tank volume at an average of 1000 GPM.
When Checking the left front or right front side of the fire apparatus, don't forget to inspect the: - ANS
saddle tanks
YC
Daily inspection - ANS Ensure auxiliary fuel tank is full
Operate pump primer
Inspect auxiliary winterization system.
D
Weekly Inspection - ANS Clean intake strainers
U
Pre-service pump certification test are conducted by: - ANS An independent testing agency
When using a static body of water as your water source during fire apparatus service testing, the water
ST
surface must not be more than___ feet above the centerline of the pump intake and the water must be at
least _____ feet deep. - ANS 10 Feet above
4 Feet deep
If the engine speed check proves the MWS apparatus is running at a different speed than what which it
was originally rated, you need to? - ANS Stop the testing until the problem is corrected.
A year has passed and its time conduct the annual vacuum test on your departments MWS apparatus.
You're following the procedures for conducting the vacuum test and you've already checked for and
, removed foreign matter from the hard suction hose. The next step to perform while conducting the
vacuum test is to: - ANS Connect 20 Feet of the hard suction hose to the pump intake connection.
When conducting a priming device test and using a pump of less than 1500 GPM, the priming device
should be able to create the necessary vacuum in ____ seconds to lift water 10 feet through 20 feet of hard
suction hose. - ANS 30 seconds
Place the steps for conducting a pumping test in the correct order. - ANS 1. Gradually speed up the pump
until the net pump discharge pressure is 150 PSI
K
2. Use a pitot tube or a flow meter to check the flow of water at the nozzle.
3.Record six different readings at 5-minute intervals for a total of 20 minutes.
C
4. Set the net pump discharge pressure to 200 PSI.
LO
5. Set the net pump discharge pressure to 250 PSI.
Pressure Control Test - ANS 1. Engage the pump and set it to the pump capacity.
2. Set the pressure control device.
YC
3. Close the discharge valves.
4. Note the pump discharge
The three parts of the pressure control test require you to close the flowing valves one at a time: - ANS
D
In no less than 3 seconds and no more than 10 seconds
The gauge and flow meter readings with actual pitot tube readings. The two readings should differ by no
U
more than: - ANS 10%
The tank to pump flow rate test measures whether the piping between an apparatus water tank and fire
ST
pump meets the minimum flow standards of: - ANS NFPA 1901
Rope or test stand - ANS Secures test nozzles
Pitot tube - ANS Measures the velocity pressure of a stream of water
Tachometer - ANS Checks engine speed
Solid stream nozzles - ANS Needed to match the volumes pumped for different tests
Compound gauge - ANS Checks the pump intake pressure
Les avantages d'acheter des résumés chez Stuvia:
Qualité garantie par les avis des clients
Les clients de Stuvia ont évalués plus de 700 000 résumés. C'est comme ça que vous savez que vous achetez les meilleurs documents.
L’achat facile et rapide
Vous pouvez payer rapidement avec iDeal, carte de crédit ou Stuvia-crédit pour les résumés. Il n'y a pas d'adhésion nécessaire.
Focus sur l’essentiel
Vos camarades écrivent eux-mêmes les notes d’étude, c’est pourquoi les documents sont toujours fiables et à jour. Cela garantit que vous arrivez rapidement au coeur du matériel.
Foire aux questions
Qu'est-ce que j'obtiens en achetant ce document ?
Vous obtenez un PDF, disponible immédiatement après votre achat. Le document acheté est accessible à tout moment, n'importe où et indéfiniment via votre profil.
Garantie de remboursement : comment ça marche ?
Notre garantie de satisfaction garantit que vous trouverez toujours un document d'étude qui vous convient. Vous remplissez un formulaire et notre équipe du service client s'occupe du reste.
Auprès de qui est-ce que j'achète ce résumé ?
Stuvia est une place de marché. Alors, vous n'achetez donc pas ce document chez nous, mais auprès du vendeur Studyclock. Stuvia facilite les paiements au vendeur.
Est-ce que j'aurai un abonnement?
Non, vous n'achetez ce résumé que pour €9,21. Vous n'êtes lié à rien après votre achat.
