Tentamen (uitwerkingen)
Solutions Manual INTRODUCTION TO MECHATRONICS AND MEASUREMENT SYSTEMS 4th Edition
- Vak
- Instelling
Solutions Manual INTRODUCTION TO MECHATRONICS AND MEASUREMENT SYSTEMS 4th Edition.
[Meer zien]Voorbeeld 4 van de 104 pagina's
Voorbeeld 4 van de 104 pagina's
In winkelwagen
In winkelwagen
Verkoper
Volgen
QuizMerchant
Ontvangen beoordelingen
Voorbeeld van de inhoud
Solutions ManualINTRODUCTION TO
MECHATRONICS AND
MEASUREMENT
SYSTEMS
4th edition
2012(c)
SOLUTIONS MANUAL
David G. Alciatore
and
Michael B. Histand
Department of Mechanical Engineering
Colorado State University
Fort Collins, CO 80523
Introduction to Mechatronics and Measurement Systems 1
,Solutions Manual
This manual contains solutions to the end-of-chapter problems in the third edition of
"Introduction to Mechatronics and Measurement Systems." Only a few of the open-ended
problems that do not have a unique answer are left for your creative solutions. More information,
including an example course outline, a suggested laboratory syllabus, MathCAD files for examples
in the book, and other supplemental material are provided on the Internet at:
mechatronics.colostate.edu
We have class-tested the textbook for several years, and it should be relatively free from
errors. However, if you notice any errors or have suggestions or advice concerning the textbook's
content or approach, please feel free to contact us via e-mail at David.Alciatore@colostate.edu.
We will post corrections for reported errors on our Web site.
Thank you for choosing our book. We hope it helps you provide your students with an
enjoyable and fruitful learning experience in the cross-disciplinary subject of mechatronics.
2 Introduction to Mechatronics and Measurement Systems
,Solutions Manual
2.1 D = 0.06408 in = 0.001628 m.
2
A = D
–6
---------- = 2.082 10
4
= 1.7 x 10-8 m, L = 1000 m
R = L
------- = 8.2
A
2.2
4
(a) R 1 = 21 10 20% so 168k R 1 252k
3
(b) R 2 = 07 10 20% so 5.6k R 2 8.4k
(c) R s = R 1 + R 2 = 217k 20% so 174k R s 260k
R1 R2
(d) R p = ------------------
-
R1 + R2
R 1MIN R 2MIN
R pMIN = -------------------------------
- = 5.43k
R 1MIN + R 2 MIN
R 1MAX R 2MAX
R pMAX = ---------------------------------
- = 8.14k
R 1 MAX + R 2 MAX
2 1
2.3 R 1 = 10 10 , R 2 = 25 10
2 1
R = ------------------- = --------------------------------------------------- = 20 10
R1 R2 10 10 25 10 1
R1 + R2 2 1
10 10 + 25 10
a = 2 = red, b = 0 = black, c = 1 = brown, d = gold
2.4 In series, the trim pot will add an adjustable value ranging from 0 to its maximum value to
the original resistor value depending on the trim setting. When in parallel, the trim pot
could be 0 perhaps causing a short. Furthermore, the trim value will not be additive with
the fixed resistor.
2.5 When the last connection is made, a spark occurs at the point of connection as the
completed circuit is formed. This spark could ignite gases produced in the battery. The
negative terminal of the battery is connected to the frame of the car, which serves as a
ground reference throughout the vehicle.
Introduction to Mechatronics and Measurement Systems 3
, Solutions Manual
2.6 No, as long as you are consistent in your application, you will obtain correct answers. If
you assume the wrong current direction, the result will be negative.
2.7 Place two 100 resistors in parallel and you immediately have a 50 resistance.
2.8 From KCL, I s = I 1 + I 2 + I 3
V V V V
so from Ohm’s Law -------s- = ------s + ------s + ------s
R eq R1 R2 R3
1 - = -----
1- + -----
1- + ----- R1 R2 R3
1- so R = ---------------------------------------------------
Therefore, ------- eq -
R eq R1 R2 R3 R2 R3 + R1 R3 + R1 R2
Is Is
2.9 From Ohm’s Law and Question 2.8, V = -------
- = ----------------------------------------------------
R eq R2 R3 + R1 R3 + R1 R2
----------------------------------------------------
R1 R2 R3
and for one resistor, V = I 1 R 1
R2 R3
Therefore, I 1 = ---------------------------------------------------- I s
R 2 R 3 + R 1 R 3 + R 1 R 2
R1 R2 R1 R2
2.10 lim ------------------- = ------------
- = R2
R1 R 1 + R 2 R1
dV dV 1 dV 2
2.11 I = C eq ------- = C 1 ---------- = C 2 ----------
dt dt dt
From KVL,
V = V1 + V2
so
dV dV dV
------- = ---------1- + ---------2-
dt dt dt
Therefore,
I - = -----
I - + -----
I- 1 1 1 C1 C2
------- so -------- = ------ + ------ or C eq = ------------------
-
C eq C1 C2 C eq C1 C2 C1 + C2
4 Introduction to Mechatronics and Measurement Systems
Voordelen van het kopen van samenvattingen bij Stuvia op een rij:
√ Verzekerd van kwaliteit door reviews
Stuvia-klanten hebben meer dan 700.000 samenvattingen beoordeeld. Zo weet je zeker dat je de beste documenten koopt!
Snel en makkelijk kopen
Je betaalt supersnel en eenmalig met iDeal, Bancontact of creditcard voor de samenvatting. Zonder lidmaatschap.
Focus op de essentie
Samenvattingen worden geschreven voor en door anderen. Daarom zijn de samenvattingen altijd betrouwbaar en actueel. Zo kom je snel tot de kern!
Veelgestelde vragen
Wat krijg ik als ik dit document koop?
Je krijgt een PDF, die direct beschikbaar is na je aankoop. Het gekochte document is altijd, overal en oneindig toegankelijk via je profiel.
Tevredenheidsgarantie: hoe werkt dat?
Onze tevredenheidsgarantie zorgt ervoor dat je altijd een studiedocument vindt dat goed bij je past. Je vult een formulier in en onze klantenservice regelt de rest.
Van wie koop ik deze samenvatting?
Stuvia is een marktplaats, je koop dit document dus niet van ons, maar van verkoper QuizMerchant. Stuvia faciliteert de betaling aan de verkoper.
Zit ik meteen vast aan een abonnement?
Nee, je koopt alleen deze samenvatting voor €17,57. Je zit daarna nergens aan vast.
Is Stuvia te vertrouwen?
4,6 sterren op Google & Trustpilot (+1000 reviews)
Afgelopen 30 dagen zijn er 77985 samenvattingen verkocht
Opgericht in 2010, al 14 jaar dé plek om samenvattingen te kopen