MSSC Quality Practices & Measurement Exam Test NEWEST ACTUAL COMPLETE QUESTIONS AND CORRECT DETAILED ANSWERS (VERIFIED ANSWERS) |ALREADY GRADED A+
4 keer bekeken 0 keer verkocht
Vak
MSSC Quality
Instelling
MSSC Quality
MSSC Quality Practices & Measurement Exam Test NEWEST ACTUAL COMPLETE QUESTIONS AND CORRECT DETAILED ANSWERS (VERIFIED ANSWERS) |ALREADY GRADED A+
Production personnel use standard operating procedures to determine __________. - Answers - The proper way to do a task
GD&T __________. - Answers...
MSSC Quality Practices & Measurement Exam
Test NEWEST ACTUAL COMPLETE QUESTIONS
AND CORRECT DETAILED ANSWERS (VERIFIED
ANSWERS) |ALREADY GRADED A+
Production personnel use standard operating procedures to determine __________. -
Answers -✔✔ The proper way to do a task
GD&T __________. - Answers -✔✔ Allows certain tolerances on part features to be
increased
1. Which type of feature is parallel to the surface being dimensioned?
A. extension line
B. dimension line
C. dimension units
D. leader line - Answers -✔✔ Dimension line
2. The three standard views of an object are __________.
- front, left side, top
- front, right side, bottom
- top, front, rear
- top, front, right side - Answers -✔✔ Top, front, right side
3. Which type of lines are used to show the counterbored hole in the part?
- hidden lines
- solid lines
- phantom lines
- dimension lines - Answers -✔✔ Hidden lines
4. The number of views in a drawing __________.
- is always 3
- is the fewest number that shows all of the features and dimensions
- is the number that needs the fewest hidden lines
- is the minimum that shows height, depth, and width - Answers -✔✔ Is the fewest
number that shows all of the features and dimensions
5. Which of the following steps is NOT used in the glass box method?
- Place object in glass box.
- Project views to the sides of the glass box.
- Rotate object in glass box.
- Unfold the glass box. - Answers -✔✔ Rotate object in glass box.
What type of drawing is shown? - Answers -✔✔ Multiview
,7. The dimensions of raw material supplied by metal suppliers are described by the
__________.
- ASTM designation
- stock size
- manufacturing Size
- series number - Answers -✔✔ Stock size
8. Which of these requires a computer?
- Sketching
- Drafting
- CAD
- Blueprinting - Answers -✔✔ CAD
9. An isometric drawing is a type of __________.
- flow chart
- pictorial drawing
- spreadsheet
- slide show - Answers -✔✔ Pictorial drawing
10. In the graphic shown, the two circles are __________.
- parallel
- concentric
- equal
- tangent - Answers -✔✔ Concentric
11. Dimensions are used to specify the __________ and location of the features of an
object.
- material
- size
- application
- cost - Answers -✔✔ Size
What feature in the figure shown is a Chamfer? - Answers -✔✔ D
13. A __________ dimension is described in inches per foot.
- Drill bit
- Lathe swing
- Shaft taper
- Countersink - Answers -✔✔ Shaft taper
14. What is the order of precedence of lines in a drawing?
- Hidden, Object, Center
- Object, Center, Hidden
- Object, Hidden, Center
,- It depends on which view is shown - Answers -✔✔ Object, Hidden, Center
15. Which of the following is not one of the six rules for dimensioning an object?
- Dimension an object completely
- Do not over dimension
- Dimension in the view that most clearly shows the feature
- Dimension hidden lines - Answers -✔✔ Dimension hidden lines
16. Engineers sometimes use a __________ to measure angles on a drawing.
- rule
- protractor
- French curve
- compass - Answers -✔✔ Protractor
17. What dimension is indicated in this graphic?
- Width
- Depth
- Height
- Diameter - Answers -✔✔ Height
18. There are 60 minutes of arc in one __________.
- second
- degree
- circle
- Diameter - Answers -✔✔ Degree
19. In manufacturing, a blueprint is also called what?
- A technical drawing
- A drafting sheet
- A schematic
- A film - Answers -✔✔ A technical drawing
20. The distance across the flats of the hex head shown in the part drawing is
__________ inches.
-2¼
-3
-1
- 1 ½ - Answers -✔✔ 2 ¼
21. The length of the part shown in the drawing is __________ inches.
-9½
-9¾
-2¼
- 5 - Answers -✔✔ 9 ¾
, 22. Which type best describes the line indicated in the graphic?
- Hidden Line
- Object Line
- Center Line
- Edge Line - Answers -✔✔ Object Line
Which of the following bolts is a grade 2? - Answers -✔✔ A
The hole shown in the graphic is a __________ hole. - Answers -✔✔ Counterbore
25. What are the two types of assembly drawings?
- part and basic
- basic and detailed
- detailed and exploded
- exploded and basic - Answers -✔✔ Exploded and basic
26. A sectional view __________.
- cuts a part into pieces so that the insides of the part can be drawn as object lines
- represents the internal features of a part when the hidden lines are not enough
- is an addition to the standard views drawn for a multiview drawing
- All of the above - Answers -✔✔ All of the above
27. Which of the following is not used to specify a threaded fastener?
- minor diameter
- class of fit
- major diameter
- fastener length - Answers -✔✔ Minor diameter
28. Two types of threads are __________.
- internal and nocturnal
- external and common
- common and special
- internal and external - Answers -✔✔ Internal and external
29. In the assembly drawing shown, part 3 screws into part __________.
-4
-5
-2
- 1 - Answers -✔✔ 4
30. The material that will be used to create the gear is indicated in the part drawing's
title block to be __________.
- cast iron
- steel
- bronze
Voordelen van het kopen van samenvattingen bij Stuvia op een rij:
√ Verzekerd van kwaliteit door reviews
Stuvia-klanten hebben meer dan 700.000 samenvattingen beoordeeld. Zo weet je zeker dat je de beste documenten koopt!
Snel en makkelijk kopen
Je betaalt supersnel en eenmalig met iDeal, Bancontact of creditcard voor de samenvatting. Zonder lidmaatschap.
Focus op de essentie
Samenvattingen worden geschreven voor en door anderen. Daarom zijn de samenvattingen altijd betrouwbaar en actueel. Zo kom je snel tot de kern!
Veelgestelde vragen
Wat krijg ik als ik dit document koop?
Je krijgt een PDF, die direct beschikbaar is na je aankoop. Het gekochte document is altijd, overal en oneindig toegankelijk via je profiel.
Tevredenheidsgarantie: hoe werkt dat?
Onze tevredenheidsgarantie zorgt ervoor dat je altijd een studiedocument vindt dat goed bij je past. Je vult een formulier in en onze klantenservice regelt de rest.
Van wie koop ik deze samenvatting?
Stuvia is een marktplaats, je koop dit document dus niet van ons, maar van verkoper Stuviaascorers. Stuvia faciliteert de betaling aan de verkoper.
Zit ik meteen vast aan een abonnement?
Nee, je koopt alleen deze samenvatting voor €14,77. Je zit daarna nergens aan vast.
