Minimum center thickness - Study guides, Class notes & Summaries

Boilermaker NCCR Test Questions And Answers Boilermaker NCCR Test 1 ft 3-3/4 in + 2 ft 1-1/16 in +5 ft 10- 7/8 in = - ANS 9 ft 3-11/16 in A 1-inch plate is to be cut. Why should an acetylene gerulator on a cutting rig not be adjusted over 15 PSI? - ANS Acetylene is unstable above this pressure A big control valve is pulled who is responsible for the rigging? - ANS Crane operator and rigger A boiler maker must have all of the following wh...

In a post tensioned Beam what is the minimum size bar used to support the beam? : #4 Bar What is the minimum height between finished floor and joist in the kitchen is 48" on center? : 7 FT How thick does a load bearing masonry need to be on a single story building? : 6 inches What chemical is used for high heat concrete : retarder when mechanical equipment is on the roof, how far from the edge of the roof should a warning line be if the equipment is running parallel to the roof edge...

In a post tensioned Beam what is the minimum size bar used to support the beam? - correct answer-#4 Bar What is the minimum height between finished floor and joist in the kitchen is 48" on center? - correct answer-7 FT How thick does a load bearing masonry need to be on a single story building? - correct answer-6 inches What chemical is used for high heat concrete - correct answer-retarder when mechanical equipment is on the roof, how far from the edge of the roof should a warning l...

In a post tensioned Beam what is the minimum size bar used to support the beam? CORRECT ANSWER #4 Bar What is the minimum height between finished floor and joist in the kitchen is 48" on center? CORRECT ANSWER 7 FT How thick does a load bearing masonry need to be on a single story building? CORRECT ANSWER 6 inches What chemical is used for high heat concrete CORRECT ANSWER retarder when mechanical equipment is on the roof, how far from the edge of the roof should a warning line be i...

transducer Electronic pulses from the pulser are applied to the ? amplification, compensation, compression, and demodulation What functions are preformed by the receiver? the ratio of the maximum to the minimum intensity that can be displayed The dynamic range of an ultrasound system is described as? frequency divided by bandwidth How is the QF of a transducer determined? PZT The most common man-made crystal is : travel time and speed Which variables must be known in order to calculat...

What is the minimum distance from exposed ground for a wood framing member that is in contact with?? 24 inches What is the maximum allowed slope for the top surface of a footing? None Where should a drip edge be used? Beneath the underlayment What is the minimum height for guard rails for balcony? 36 inches What test is performed to determine the drainage capacity of a soil? Perculation test- Perc Test What is the minimum width of footings used for a one s...

Nicet Highway Construction Level 2 Questions and Answers Already Passed What are the 5 types of bridge abutments? Closed Abutment, Stub or Perched Abutment, Pedestal or Spill-through Abutment, Integral End Bents, Mechanically Stabilized Abutment What is a "closed abutment"? A closed abutment is a full-height wall with wing walls on each side that retains the full height of the approach embankment. This type of abutment minimizes the required span length of the bridge. What is a stub or perc...

DASLE MN State Exam || Questions & Answers (Graded A+) DASLE MN State Exam || Questions & Answers (Graded A+) What prophy paste is not recommended for esthetic restorations? - ANSWER - regular prophy paste Low-abrasive pastes such as micron-fine sapphire or diamond paste or aluminum oxide paste should be used for restorations. Factors that influence the rate of abrasion - ANSWER - The more agent used, the greater the degree of abrasion. The lighter the pressure, the less abrasion. ...

NCLE Practical Questions and Answers Verified A+ Steep Fluorescein Pattern - Bright green pooling center, very faint green pooling on diameter of lens Flat Fluorescein Pattern - Bright green pooling on diameter of lens, very faint green in center Against-the-rule Astigmatism Pattern - Bright green pooling horizontally, faint green pooling vertically With-the-rule Astigmatism Pattern - Bright green pooling vertically, faint green pooling horizontally Pri...

API 653 Certification Practice Exam Open Book 68 Questions with Verified Answers An insert plate is required for a new 4 NPS nozzle (4.5" O.D.) in the shell. What is the minimum diameter for this insert? A. 4.5" B. 9" C. 12" D. 16.5" - CORRECT ANSWER D. 16.5" A welder is qualified on a plate in the 3G position. The welder is qualified for what fillet weld position(s)? A. None B. F, H C. F, H, V D. All fillets - CORRECT ANSWER C. F, H, V When must a shim be placed under...