Roof deck - Study guides, Class notes & Summaries

Is the home inspector required to walk on the roof? - Answer no I. The inspector shall inspect from ground level or the eaves: - Answer the roof-covering materials; the gutters; the downspouts; the vents, flashing, skylights, chimney, and other roof penetrations; and the general structure of the roof from the readily accessible panels, doors or stairs. The inspector shall only need to describe - Answer the type of roof covering material the inspector shall report as in need of corre...

Professional Home Inspector state Exam Guide final 2024 tested and verified The inspector is not required to determine ____ ___ of any system or component. - CORRECT ANSWER--Years of age -Life expectancy -Make model Horizontal waste pipe should slope ____ inch per foot - CORRECT ANSWER-1/4" per foot if < 3 inch pipe. 1/8" per foot if > or = to 3 inch pipe Drip screed - CORRECT ANSWER-Also called weep screed. Used at the base/bottom of stucco walls to release moisture. Pressur...

The inspector is not required to determine ____ ___ of any system or component. - Answer- -Years of age -Life expectancy -Make model Horizontal waste pipe should slope ____ inch per foot - Answer- 1/4" per foot if < 3 inch pipe. 1/8" per foot if > or = to 3 inch pipe Drip screed - Answer- Also called weep screed. Used at the base/bottom of stucco walls to release moisture. Pressure Vacuum Breaker (PVB) - Answer- Used for Backflow Prevention. Lawn Irrigation systems: install...

What is the minimum exposure on a 24 inch wood shingle? A)5-1/2 inches B)6-1/2 inches C) 4 inches D)5 inches - Answer 5 inches Which of the following locations would NOT typically have an expansion joint on a built up roof? A)every 100 lineal feet of roof B)where substantial temperature variations occur in the occupancy below the roof C)at new additions to an existing roof D)where the roof intersects a vertical wall - Answer Every 100 lineal feet of roof What is the ASTM...

Is the home inspector required to walk on the roof? CORRECT ANSWER no I. The inspector shall inspect from ground level or the eaves: CORRECT ANSWER the roof-covering materials; the gutters; the downspouts; the vents, flashing, skylights, chimney, and other roof penetrations; and the general structure of the roof from the readily accessible panels, doors or stairs. The inspector shall only need to describe CORRECT ANSWER the type of roof covering material the inspector shall report a...

Who may use API RP 575? Anyone desiring to use API RP 575 may do so. API RP 575 covers: maintenance and inspection of atmosphere and low-pressure storage tanks. The generic meaning for atmosperic pressure is up to but not exceeding _______ ibf/in2 gage pressure. 2.5 The exterior surface of the tank bottom is known as the : bottom- side. When describing the amount of product the tank can hold, it is referred to as: shell capacity The pressure on the surface of a confined liquid caused by t...

How is a diamond condition fixed? - ANSWER-By pulling the damage for length. Diamond is a length condition. When measuring a unibody vehicle, it is discovered that the left front rail is 111mm from spec in width. What condition is this? - ANSWER-Width is calculated from the center out, so a value of -111mm on the left rail shows sway to the right and in toward centerline. A collision damaged vehicle is discovered to be down in height at opposite end of the center section. - ANSWER-Twist co...

T/F: Ventilation of attic areas is intended to prevent the accumulation of moisture vapor in the attic-roof space and to dry low levels of condensation that may form on the underside of a roof deck. - ️️True There should be a minimum space of ____ provided between the insulation and the roof deck sheathing and at the location of the vent. - ️️1 inch T/F: A combination of continuous ridge vents along the peak of the roof and continuous soffit vents at the eaves provides the most eff...

0.020" thick aluminum is approximately: - 24 gage 0.020" thick copper approximately equals: - 24 gage, B&S A 10' length of stainless steel will expand _______ with a temperature increase of 100*F - 1/8" A fire extinguisher must be tested every: - Year A railing is required on work surfaces _______ or higher from the ground. - 7 1/2 ft A roof is considered to be low-pitched when its slope is: - 3:12 or less A roof with a slope of 8:12 is considered what pitch? - 1/3 pitch A roofing con...

The inspector is not required to determine ____ ___ of any system or component. - ANSWER -Years of age -Life expectancy -Make model Drip screed - ANSWER Also called weep Horizontal waste pipe should slope ____ inch per foot - ANSWER 1/4" per foot if < 3 inch pipe. 1/8" per foot if > or = to 3 inch pipe screed. Used at the base/bottom of stucco walls to release moisture. Pressure Vacuum Breaker (PVB) - ANSWER Used for Backflow Prevention. Lawn Irrigation systems: installed v...