Condensate drain - Study guides, Class notes & Summaries

4th Class Power Engineering Unit A12 Chapter 4: Feed water Systems Already Passed With this system, not electrical power is required to feed make-up water to the boiler: Select one: a. gravity return system b. pump return system c. low flow return system d. high side return system a These are similar to combined feedwater feeder/cut-offs, with the exception that they do not have integral mechanically operated control valves: Select one: a. float control feeders b. float contro...

One of the legal responsibilities of the engineer during an inspection is: Select one: a. To notify the Workers Compensation Board of the inspection b. Point out any known or suspected defects to the inspector c. To have at least two staff members present at all times d. To be in possession of an inspection certificate - ANSWER b The _____ tubes of a fired hot oil heater have fins on their outer surfaces. Select one: a. Water b. Radiant c. Extended type d. Fire - ANSWER c The...

3rd Class Stationary Steam Engineer License Prep Exam 2024 Questions and Answers. _________ are necessary for complete combustion - Answer<>time, temperature, mixture, and atomization if the steam pressure gauge indicates 200 PSIG, the absolute pressure is______ - Answer<>214.7 a boiler is operating at 400 PSI, and the safety valve opens at 410 PSI and closes at 398 PSI. The blowdown is______psi - Answer<>12 an oil cooler is commonly used with a(n) ________ when operatin...

When loading a steam sterilizer, basins should be (A) placed in an upright position. (B) loaded first. (C) placed on edge. (D) placed in a wire basket. C The higher the bioburden on an object (A) the more difficult it will be to sterilize. (B) the less time it will take to sterilize it. (C) the more biological tests will be needed in the load. (D) the longer it will take to cool after sterilization. A When combining loads, hard goods should be placed on the top shelve...

3rd Class Stationary Steam Engineer License Prep Exam 2024 Questions and Answers. ____ are necessary for complete combustion - Answer<>time, temperature, mixture, and atomization if the steam pressure gauge indicates 200 PSIG, the absolute pressure is______ - Answer<>214.7 a boiler is operating at 400 PSI, and the safety valve opens at 410 PSI and closes at 398 PSI. The blowdown is______psi - Answer<>12 an oil cooler is commonly used with a(n) ________ when operating in ...

Home Inspection Course National Preparation Exam Q&A 2024 The main difference between a laundry tub pump and a sump pump is (a) laundry tub pumps can handle lint (b) sump pumps are laundry capacity (c) laundry tub pumps operate on 120 volt, and sump pumps operate only on 240v power (d) sump pumps are manual, and laundry tub pumps are automatic - CORRECT ANSWER-(a) laundry tub pumps can handle lint All of the following are common HRV problems except (a) missing filters (b) dirty h...

Texas Home Inspection Questions and Answers Already Passed How big is the fillpipe for an underground oil tank? 2 inches The minimum size for a dryer vent is? 4 inches What is the maximum spacing between supports for a horizontal nonmetallic flexible air duct? 4 feet True or false A furnace can be in a laundry room? True How far should a hearth extend if the opening of the fireplace is less than 6 feet? 16 inches How far should a hearth extend if the opening of the firep...

Plumbing Red Seal Questions Trap arms and fixture drains are to be installed with roughly _____ of an inch downward slope for every foot of trap arm length - 1/4" per foot less than 3" - 1/8" per foot 4" and higher What can put a great deal of stress on your neck, shoulders, back, and legs when lifting heavy objects? - not bending at your knees and keeping your back straight The Propane Storage and Handling Code is ______________. - B149.2-00 The wires of a thermostat are wired...

Describe the ship's service air compressor in the engine room (not the AMR): what is the approximate receiver pressure, how is the coolant oil level checked, and how is coolant oil added? - 2 atlas copco GA15, ship service & control air, oil added by filler plug when compressor is off Describe operation of the compressed air dryers and their location, what air system(s) do they serve? - 2 atlas copco FD40, removes moisture from control air, two heat exchanger allow the water to condense H...

Can mold be found anywhere? - ANS yes, they can grow on virtually any organic substance (food) What is needed for mold to grow? - ANS moisture and oxygen must be present What is the key to mold control? - ANS Moisture control According to the EPA, what is the ideal RH? - ANS 30 - 50% (below 60%) If water is detected how quickly should it be cleaned and dried to prevent mold growth? - ANS within 48 hours What are the EPA regulations for mold? - ANS There are no EP...