Fcaw plate - Study guides, Class notes & Summaries

API 653 exam prep Closed book ONLY Questions and Answers 100% Pass API 653 defines a "Storage tank engineer" as: A) A registered professional engineer in structural steel fabrication B) Person or organization who is knowledgeable and experienced in the engineering disciplines associated with evaluating the integrity and reliability of aboveground storage tanks C) the engineering department of a contractor who makes repairs to aboveground storage tanks D) A professional engineer wh...

ICC Welding Practice Questions with Correct A Given, a column is 29 feet long. What is the maximum variation in straightness? - Answer-0.3625; D1.1 5.23.1 Reference is made to Figure 6.4 in AWS D1.1, 2006. What is the maximum size discontinuity allowed in 3/4" thick complete penetration groove weld ? - Answer-1-1/16"; D1.1 F6.4(a) If welding ASTM A913 steel of thickness exceeding 1 1/2 inches (38 mm) without use of preheat, what is the maximum diffusible hydrogen permitted from the ...

CWB Level 2 Closed Book Questions and Answers 100% Pass To measure the strength of a welded joint what mechanical test would you prescribe? a) A transverse weld tension test. b) A charpy test. c) A CTOD test. d) An all weld metal tension test. e) A side bend test. a) A transverse weld tension test. Select the cutting process that would provide the narrowest heat affected zone when cutting 12.5 mm (0.5 in) thick carbon steel. a) Oxy-acetylene cutting. b) Air-carbon arc cutting. c) Oxy-pr...

W59 Rev.1 Questions and Answers 100% Pass CSA Standard W59 contains provisions for which of the following welding processes? SMAW, GMAW, SAW, SW, FCAW, EGW, ESW, MCAW The provisions of CSA Standard W59 are not intended for use with steels having a specified minimum yield strength of over 700 Mpa (100,000 psi). True What is a low hydrogen electrode? An electrode depositing weld metal having a specified maximum limit to the diffusible hydrogen content. "Contractor" refers to: The fabricator ...

W47.1 Practice One Questions and Answers Rated A+ CSA Standard W47.1 provides the requirements that must be met and adhered to by a company seeking certification. True CSA Standard W47.1 provides the requirements that must be met and adhered to by a company seeking certification True Certification can be considered as an approval of the products fabricated by a certified company False What does Class refer to? F,H,V & O welding positions flat (F), horizontal (H), vertical (V), or overhead (O...

API 653 exam prep Closed book ONLY Graded A+ API 653 defines a "Storage tank engineer" as: A) A registered professional engineer in structural steel fabrication B) Person or organization who is knowledgeable and experienced in the engineering disciplines associated with evaluating the integrity and reliability of aboveground storage tanks C) the engineering department of a contractor who makes repairs to aboveground storage tanks D) A professional engineer who is also an authorized...

CO2 shielding gas on FCAW - Answer widely used, low cost, deep arc penetration, relatively inert at room temp., dissociates at arc temps., allow for oxidation in the weld pool. Textbook: 6.5-1 - 6.5-4 Ar-CO2 shielding gas for FCAW - Answer allows for greater oxidation resistance, most common ratio is: 75% Ar, 25% CO2, generally gives welds higher tensile & yield strengths than welds of 100% CO2, spray mode mixture, Excessive amounts of filler materials (Mn, Si, Al) will change mech. propertie...

Welding - Chapters 1-6 - First Exam, With Complete Verified Solution List welding Currents: AC,DC-,DC+ What is the Definition of welding current the current in the welding circuit during the making of the weld. Three units are used to measure welding current Voltage: electrical pressure Amperage: number of electrons flowing Wattage: power of the arc What approximately is The temperature of the arc? 11,000°F (6000°C). Three different types of current used for welding are Alternati...

CWB 1 Exam Questions & Answers | 115 Questions with 100% Correct Answers | Updated & Verified | 37 Pages 1. Which is not a recommended method for surface cleaning of a part for liquid penetrant examination? a) Cleaning with organic solvents. b) Blasting with shot or dull sand. c) Cleaning with de-greasers. d) Use of de-scaling solutions. e) Ultrasonic cleaning methods. - Answer ️️ -b) Blasting with shot or dull sand. 2. Which of the following weld defects is most likely to be misse...