Fuel metering systems 2 - Study guides, Class notes & Summaries

  1. The inspection of water based foam fire suppression piping systems may be performed by a valid C of F holder. S-15 Answer: S-15 2. A concentrate based on fluorinated surfactants with a foam stabilizer and diluted with water to a 1 percent, 3 percent or 6 percent solution is best described as a(n) Answer: Answer: Aqueous Film Forming Concentrate (AFFF) 3. A shall be painted red with contrasting bright caps. Answer: Fire Department foam connection, orange 4. What type of fire p...

Accounting Associate Degree General Education Core (Required minimum: 15 Semester Credit Hours) Area I - Language Arts/Communication ENGL 1101 Composition and Rhetoric 3 180 Explores the analysis of literature and articles about issues in the humanities and in society. Students practice various modes of writing, ranging from exposition to argumentation and persuasion. The course includes a review of standard grammatical and stylistic usage in proofreading and editing. An introduction to...

You are an external BA with a frequency bais of 20 MW/.1 Hz that sees a frequency of 60.02 due to a large loss of load in the contingent BA. If your generator governor control systems responded to the frequency deviation approximately how much of a generation change would you BA experience? -4MW Net actual interchange minus Net scheduled interchange is what? Inadvertent interchange Suppose your interconnection operators at 59.97 Hz from one minute after midnight to noon and operate a...

A transmission line is operating with a voltage phase angle different of 30 degrees between the sending Vs and the receiving bus Vr. If the receiving end load is suddenly increased, the voltage phase angle difference will be? The phase angle will increase. When load is increased phase angle will increase. A load has a power factor of 0.9 lagging. If the load draws 100 MVA, what is the MW draw? 90 pf= mw/mva The high side of a delta-wye connection transformer is connected to a power s...

R-22 vapor line diameters and lengths are typically specified for a vapor pressure drop that does not exceed... 6-7 psi or 6°F The primary purpose of using flux when soldering copper or brass parts is to... Prevent oxidation The water that results from a defrost cycle of an air to air heat pump (runoff) must drain off and away from the outdoor coil to... Prevent excessive ice can build up on the bottom of the coil and reduce capacity The component used to reduce sound tr...

Hospitality Facilities Management Final | 2023/2024 latest questions and answers Which of the following statements regarding a building's initial construction and ongoing maintenance costs is true? - The more a building costs initially to construct, the more it generally costs to maintain it Maintenance that includes preparing equipment for changes in the seasons is called: - scheduled maintenance Which of the following is not a CapEx item? - telecommunications trunk line charges The t...

If a Balancing Authority does not comply with the Control Performance Standard, the Balancing Authority is not permitted to provide which of the following for any other Balancing Authority entities? Regulation of other services related to control performance 1. It is the obligation of each Balancing Authority to fulfill its commitment to the Interconnection and not ________ the other balancing Authorities in the Interconnection Burden A Balancing Authority is performing Overlap Regul...

R-22 vapor line diameters and lengths are typically specified for a... Vapor pressure drop that does not exceed a 6-7psi or 6 degrees F The primary purpose of using flux when soldering copper or brass parts is... To prevent oxidation The water that results from a defrost cycle of an air to air heat pump(runoff) must... Drain off and away fro the outdoor coil to prevent excessive ice build up on the bottom of the coil and reduce capacity The component used to reduce sound ...

1. 1. On a car with disc/drum brakes, the front brakes grab quickly when light pedal pressure is applied. This problem could be caused by a bad: A. proportioning valve B. pressure safety switch C. metering valve D. residual check valve: 1. The correct answer is C. The metering valve delays the flow of brake fluid to the front calipers until the pressure in the system rises to a point where the wheel cylinder can overcome the tension of the brake shoe return springs. The purpose is to have b...

R-22 vapor line diameters and lengths are typically specified for a: Vapor pressure drop that does not exceed 6 - 7 psi or 6°F. The primary purpose of using flux when soldering copper or brass parts is to: Prevent oxidation. The water that results from a defrost cycle of an air to air heat pump (runoff) must: Drain off and away from the outdoor coil to prevent excessive ice can build up on the bottom of the coil and reduce capacity. The component used to reduce sound tra...