Gear and bearing - Study guides, Class notes & Summaries

1 MISSOURI BOATING LICENSE EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+ Bow Correct Answer: Front of the vessel. Stern Correct Answer: Rear of the vessel. Starboard Correct Answer: Right side of the vessel. Port Correct Answer: Left side of the vessel. Hull Correct Answer: Body of the vessel. Gunwale Correct Answer: Upper edge of vessel's side. 2 Cleat Correct Answer: Metal fitting on which a rope can be fastened. Propeller Correct Answer: Rotates and...

The one of the following types of oils MOST preferred for the hydraulic governor of a reciprocating steam engine is______ oil. Non-additive turbine type Oil The one of the following pumps that does NOT have moving parts to be lubricated is a ______ pump jet The LARGEST class of lubricants in common use is Mineral oil The sealing fluid in lubricating oil centrifuges is water In a well - operated lubricating oil and grease storage facility , lubricating oil is NOT normally removed from lar...

Which of the following is the proper way to adjust the rack yoke bearing? A. Tighten to 75 ft lbs. B. Tighten to 5 inch lbs. C. Tighten and then back off the original equipment manufacturer's (OEM) specifications. D. Tighten to 0.002" end-play. Tighten and then back off the originial equipment manufacturer's (OEM) specifications. Many OEMs will recommend that the technician tighten to a specification then back off a certain number of degrees. A customer says that the steering whee...

MANUAL TRANSMISSION MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS WHEN REPLACING A LEAKING REAR AXEL SEAL, YOU FIND THE AXLE IS PITTED IN THE WHEEL BEARING AREA. WHAT SHOULD YOU DO? - Correct Answer ️️ -A. INSTALL A SLEEVE OVER THE AXEL AND REPLACE THE SEAL. B. INTALL A NEW AXLE, WHEEL BEARING, AND SEAL. (POSSIBLE CORRECT AWNSER) C. POLISH THE AXLE BEFORE INSTALLING IT. D. MACHINE THE AXEL UNDERSIZE, AND REPLACE THE WHEEL BEARING AND SEAL. (NOT CORRECT AWNSER) AS YOU CHECK...

Which of the following is true about control arm bushings? A: They are located between the frame and the control arm. B: Worn control arm bushings result wheel shimmy. C: They are tightened on while unloaded and the vehicle is raised in the air D: Both A or B - Answer-D: Both A or B Technician A says that leaf spring shackle swivels and allows the spring to flatten as the vehicle travels over bumps in the road. Technician B says that a single crack in the longest blade of a multi-leaf lea...

The texture of an aluminum-soap lubricating grease is _________ - Answer-Stringy The property of a lubricant the allows it to adhere to metallic surfaces is known as ________ - AnswerOiliness The physical appearance of a grease with a consistency number of four is MOST NEARLY _________ - Answer-Hard The one of the following measures that is commonly used to represent a rate of oil feed is drops per ________ - Answer-Minute The MOST important single property of a lubricating oil is its ____...

Millwright Level 4 practice test review Exam Questions And Answers The best method of alignment to apply when shafts can not be axially secured is? cross dialing Sag corrections in dial setting are applied only to? vertical rim readings limitations in use of cross dialing methods include substantial brackets for long spans, less accuracy over short spans, and? both shafts must turn optalign plus alignment requires the transducer assembly be mounted upon the? primary equipment dependin...

An excessively low lubricant level will most likely cause ______. a. gear clash b. hard shifting c. gear lockup d. gear jump-out - Answer- c. gear lockup Using a lubricant that is thicker than service manual specifications can lead to ______. a. gear jump-out b. hard shifting c. gear lockup d. gear slippage - Answer- b. hard shifting Manual transmission/transaxle lubricants in use today include ______. a. automatic transmission fluids b. engine oils c. multiple visc...

What type of pump uses the throwing force of a rapidly revolving impeller? CENTRIFUGAL Which pump uses a piston to move a fluid? reciprocating The indirect heat exchanger that uses one tube inside another tube is known as what type construction? DOUBLE TUBE Heat transfer from physical contact between two substances is known as CONDUCTION What is used to connect turbines and reduction gear while allowing slight misalignment? HIGH SPEED FLEXIBLE COUPLINGS The gear cut used to reduce axial ...

A fixed volume of liquid is discharged by a centrifugal pump (TRUE/FALSE) - correct answer False Which centrifugal pump component prevents reverse flowof liquid through the pump? - correct answer Check valve What is used to move fluid from one location to another? - correct answer Pump What centrifugal pump component rotates and causes centrifugal for...