5 coating - Study guides, Class notes & Summaries

EPA Lead Inspector questions and answers latest top score. Lead-based paint (LBP) - correct answers.Any varnish, shallac, or coating that contains either- 1.0 mg/cm2 - 0.5 % by weight - 5000 ppm - Older instruments could not read accurately at 0.7, so the lead standard was updated to 1.0 Dust sample clearance values - correct answers.- Floors: 40 μg/ft2 > 10 μg/ft2 (10 μg/ft2 in NY) - Windows: 250 μg/ft2 > 100 μg/ft2 (50 μg/ft2 in NY) - Window wells (troug...

NACE CIP 1 CBT Exam (Quizzes and Study Questions) How is the process of steel corrosion ALWAYS described? - Correct answerelectrochemical Based on the galvanic series presented in the NACE CIP Level 1 Manual, which three can be used effectively as galvanic anodes for carbon steel? - Correct answer-zinc, aluminum, magnesium A decrease in temperature will generally cause the corrosion rate to _____ - Correct answer-decrease The electrolyte is a medium which carries the following type of current?...

12" - Answer- A foundation drain shall extend past the outside edge of the footing at least how far? 3/8" - Answer- A concrete masonry foundation wall extends below grade and will require parge coating using Portland cement mortar. What is the minimum allowable thickness? contacting the local utility companies - Answer- Which is the first step that needs to be taken prior to starting any excavation work? conducting test borings - Answer- Before excavating for a new building, how shoul...

NACE CIP 1 CBT EXAM PRACTICE 20242025 Questions & Answers | with 100% Correct Answers | Updated & Verified .1. Dew point is the temperature at which ANS condensation occurs. 2. You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining. Your FIRST preferred course of action is to ANS Document the problem and advise the Contractor and Owner's represe...

Hand Hygiene Turn on the water and adjust it to a comfortable, warm temperature. Wet the hands, keeping the hands lower than the elbows. Apply 3 to 5 mL of soap to the hands, coating all surfaces. Rub the hands vigorously together, working up a lather, for at least 15 seconds. Rinse thoroughly, pointing the fingers down to allow water to run off the hands. Dry the hands from the fingers to the wrist. Turn off the water with a clean paper towel. Alcohol-based handrub

Boiler Maker Union Test Questions and Answers Already Passed Subtract: 9_1/8 - 2_11/24 = -6 2/3 -6 1/2 -6 1/4 -6 3/4 6_2/3 A boilermaker mechanic requires 12 lengths of 1/4" membrane. Each length measures 12' 7''. What is the total length of membrane needed? -150' 7'' -150' 10'' -151' -151' 4'' 151' A welder needs tube sections (Dutchmen) in the following lengths: 8' 10'', 12' 5'', and 9' 11''. What is the overall amount of tubing needed? -31' -31' 2''...

NACE CIP 1 CBT Exam (Quizzes and Study Questions) with 100% Correct Answers How is the process of steel corrosion ALWAYS described? - Answer-electrochemical Based on the galvanic series presented in the NACE CIP Level 1 Manual, which three can be used effectively as galvanic anodes for carbon steel? - Answer-zinc, aluminum, magnesium A decrease in temperature will generally cause the corrosion rate to _____ - Answer- decrease The electrolyte is a medium which carries the following type o...

Kentucky UST Certification Test Prep Exam | 160 Questions Verified Answers (Latest Update 2024). 1. when tanks arrive at the job site, how should they be unloaded? - correct answers lifted off with a cable attached to the tank lifting lugs As an alternative lifting method, should a cable or chain be wrapped around the tank? - correct answers No, Never! When you are lifting a tank, using the lifting lugs, which of these procedures should be followed? - correct answers attach a triangle cabl...

Hand Hygiene Turn on the water and adjust it to a comfortable, warm temperature. Wet the hands, keeping the hands lower than the elbows. Apply 3 to 5 mL of soap to the hands, coating all surfaces. Rub the hands vigorously together, working up a lather, for at least 15 seconds. Rinse thoroughly, pointing the fingers down to allow water to run off the hands. Dry the hands from the fingers to the wrist. Turn off the water with a clean paper towel. Alcohol-based handrub Apply 3 to 5 mL (per m...

NACE CIP 2 Study Guides 2024 with Answers 100% Pass What is the cause of chalking in epoxy coating - Answer-UV or radiation exposure What is polymerization cured coating? - Answer-Two parts mixed together just prior to use Examples of non-convertible coatings - Answer-1. Chlorinated rubber 2. Vinyl 3. Acrylic 4. Bituminous Non-convertible curing def. - Answer-No chemical change during cure cycle Convertible curing def. - Answer-Some chemical change during cure cycle What info should be ...