Minimum center thickness - Study guides, Class notes & Summaries

VA Contractors State License Test – With Complete Questions & Answers (Rated A+) VA Contractors State License Test – With Complete Questions & Answers (Rated A+) Who should inspect a trench daily for safety? - ANSWER - A competent person What is the first thing an individual should check before entering a confined space? - ANSWER - Availability for breathable air Wood shims should not be used to level beams and girders because they are? - ANSWER - Compressible What is the maximu...

ASE ASSOCIATE EXAM 2024 WITH 100% ACCURATE SOLUTIONS Brake Pad Minimum Thickness Customer Pay Warranty CPO - ANSWER ☑☑Customer Pay: 3mm Warranty: 4mm (3.9mm) CPO: 5 mm Brake bleed pressure setting (bar): - ANSWER ☑☑2 bar max - Location of MSDS: - ANSWER ☑☑Online CPO test drive (length and distance): - ANSWER ☑☑20 uninterrupted minutes/ 5 continuous miles Caliper bleeding with 2 bleed screws - ANSWER ☑☑Outer bleeder first, then inner - Is pres...

Review of API-653 Questions and Answers 100% Pass Replacement shell plate may be circular,oblong,square with rounded corners or rectangular with rounded corners except when: - Correct Answer ️️ -an entire shell plate is replaced Shell replacement patch plates shall be welded with butt joints with complete penetration and complete fusion, except as: - Correct Answer ️️ -permitted for lapped patch shell repairs Joints in lap-welded shell tanks: - Correct Answer ️️ -may be repair...

the shear capacity for horizontal wood frame gypsum board diaphragm ceiling is how many POF for gypsum board 1/2 inch thick with 16 on Center spacing of - 90 plf in exterior plaster, a minimum of 0.019 of an inch number 26 galvanized galvanized sheet gauge corrosion resistant weep screed with a minimum vertical attachment flange of what must be provided at or below the foundation plate line on exterior wall studs - three and a half inch in exterior plaster, the weep screed must be placed a ...

IICL Chassis Inspector Exam What is the inspection criteria for brake linings? CORRECT ANSWER: Visually check for thickness; oil/grease saturation; separation from shoes; cracking; chipping. What is the minimum acceptable brake lining thickness? CORRECT ANSWER: No less than 1/4" at the shoe center What is heat checking on a brake drum? CORRECT ANSWER: Normal condition where the appearance of numerous short, fine hairline cracking on the braking surface of drum appear.

Airframe ASA-Baker's School FAA Oral Questions and Answers What are three requirements for a repair to a piece of sheet metal aircraft structure? - Answer ️️ -The repair must restore the lost a) strength, b) rigidity, and c) aerodynamic shape must not change. When making a riveted repair to an aircraft sheet metal structure, which should be stronger, the shear strength of the rivet, or the bearing strength of the metal sheet? - Answer ️️ -The two strengths should be close to each...

Virginia Hic Questions and Answers Already Passed The MINIMUN length drywall screw for installing 1/2 inch gypsum board to wood studs is 1 1/4 inches What is the MINIMUM breaking strength required of safety belt lanyards 5,400 pounds What is the MINIMUM clearance that combustible insulation MUST other heat-producing devices 1 inch What is the MAXIMUM flame spread index for insulation materials 25 The amount of water per sack of cement is what controls all EXCEPT Wear resistan...

Airframe ASA-Baker's School FAA Oral Questions and Answers What are three requirements for a repair to a piece of sheet metal aircraft structure? - Answer ️️ -The repair must restore the lost a) strength, b) rigidity, and c) aerodynamic shape must not change. When making a riveted repair to an aircraft sheet metal structure, which should be stronger, the shear strength of the rivet, or the bearing strength of the metal sheet? - Answer ️️ -The two strengths should be close to each...

API 653 CLOSED BOOK Exam 100 Questions with Verified Answers Two methods of quantifying the remaining thickness of tank bottoms are mentioned in API 653. One method uses the formula involving "MRT". What is the name of the other method? a. Deterministic and Analytic b. Methodological and Non-destructive c. Quantitative and Destructive d. Probabilistic and Deterministic - CORRECT ANSWER Probabilistic and Deterministic What is the maximum out-of-plumbness allowed from the top of the sh...

ADEX OSCE Exam Questions and Answers 100% Pass thickness of minor RPD connectors - Correct Answer ️️ -1.5 mm Minimum space between vertical components of RPD - Correct Answer ️️ -5 mm Kennedy Class I - Correct Answer ️️ -bilateral distal extension Kennedy Class II - Correct Answer ️️ -unilateral distal extension Kennedy Class III - Correct Answer ️️ -entirely tooth born with teeth anterior and posterior Kennedy Class IV - Correct Answer ️️ -edentulous area anterior...