Closet flange - Study guides, Class notes & Summaries

Common Plumbing Fittings 45 Degree Elbow 45 Degree Street Elbow Reducing Bell Closet Flange Supply Line Valve PVC P Trap Threaded Coupling Threaded Union 90 Degree Threaded Street Elbow Threaded Nipple Threaded Shoulder Nipple Reducing Bushing Copper Slip Fit 90 Degree Elbow Threaded Cap Threaded T Threaded 90 Degree Elbow 90 Degree PVC Slip Fit Elbow Copper Slip Fit Coupling Chrome Finished P Trap Bronze Drop Ear Fit...

A 4-inch by 3-inch closet bend shall be acceptable. T/F correct answer: True (IPC 425.4) What is the minimum number of toilets in an educational facility men's room if the facility enrolls 500 people? correct answer: 10 (IPC 403.1) "Drinking fountains shall be located on a/an ____________ route." correct answer: accessable What is the minimum waste connection for an automatic clothes washer? correct answer: 2" (IPC 406.2) Water closet compartments shall be not less than _____...

Plumbing UPC Exam Questions With 100% Correct Answers. ABS - answerAcrylonitrile Butadiene Styrene Accessible - answerWhen applied to a fixture, connection, appliance or equipment, shall mean having access thereto, but which may require prior removal of an access panel, door or similar obstruction readily accessible - answerDirect access without the necessity of removing any panel, door or similar obstruction Airbreak - answerA physical separation. which may be a low inlet into the indir...

A combination waste-and-vent system is limited to the installation of - floor drains and sinks A permit from the _________ & ________ shall be obtained for the installation of an unvented gas fired space room heater. - Fire Dept. & Gas Inspector 1. Any structure, in which a building drain is installed, shall have as a minimum one full size main stack vent or a vent stack no less than - three inches in diameter 2. Small Pipe - 12 Inch Clearance. Cleanouts smaller than three inches shall be s...

__________ traps are not permitted. (Plumbing) - S- - Common for sinks in older houses - Can work fine if properly vented - Should report on presence and explain potential problems ____________ are best described as short lengths of pipe attached directly to a fixture by means of a flange for connection to other piping or traps. - Tailpieces ____________ must be set to discharge at a temperature not higher than 210F (99C). - Temperature Pressure-Relief Valves ________________ installed o...

Home Maintenance For Dummies 3rd Edition 2024 with complete solutions Table of Contents Cover Title Page Copyright Introduction About This Book Conventions Used in This Book What You’re Not to Read Foolish Assumptions How This Book Is Organized Icons Used in This Book Beyond the Book Where to Go from Here Part 1: Home Maintenance and You Chapter 1: Home Maintenance: What It Is and Why It Matters Keeping Up with Upkeep Benefiting from a Little TLC Ready-Set-Go! Chapter 2: ...

A 4-inch by 3-inch closet bend shall be acceptable. T/F - Answer-True (IPC 425.4) What is the minimum number of toilets in an educational facility men's room if the facility enrolls 500 people? - Answer-10 (IPC 403.1) "Drinking fountains shall be located on a/an ____________ route." - Answer-accessable What is the minimum waste connection for an automatic clothes washer? - Answer-2" (IPC 406.2) Water closet compartments shall be not less than _____ inches in width and _____ inches in de...

A(n) _____________ is a type of bend with small openings that allows you to connect a smaller pipe to the main line. correct answersheel inlet _____________ are fittings designed to hold a water seal, which prevents sewer gas from escaping into the building. correct answersTraps The __________ used to join no-hub pipes have three components: a gasket, a stainless steel shield, and clamps. correct answerscoupling The fitting that connects the water closet to the closet bend is a(n) _____...

Plumbing Journeyman Exam Questions and Answers 100% Solved True (IPC 425.4) - answerA 4-inch by 3-inch closet bend shall be acceptable. T/F 10 (IPC 403.1) - answerWhat is the minimum number of toilets in an educational facility men's room if the facility enrolls 500 people? accessable - answer"Drinking fountains shall be located on a/an ____________ route." 2" (IPC 406.2) - answerWhat is the minimum waste connection for an automatic clothes washer? 30", 56" (IPC 405.3.1) - answerWa...

Plumbing Journeyman Exam Questions and Answers 100% Solved True (IPC 425.4) - answerA 4-inch by 3-inch closet bend shall be acceptable. T/F 10 (IPC 403.1) - answerWhat is the minimum number of toilets in an educational facility men's room if the facility enrolls 500 people? accessable - answer"Drinking fountains shall be located on a/an ____________ route." 2" (IPC 406.2) - answerWhat is the minimum waste connection for an automatic clothes washer? 30", 56" (IPC 405.3.1) - answerWa...