Conduit fittings - Study guides, Class notes & Summaries

Journeyman Electrician Exam Questions and Answers 2023 Graded A+ For other than one-and two-family dwellings, when building a new electrical service, at least one (1) 125-volt, single-phase, 15- or 20-ampere-rated receptacle outlet shall be located within at LEAST _____ of the electrical service equipment? -ANS>> 50 feet The ampacity of a conductor is defined by the NEC to be the maximum current, in amperes, a conductor can carry continuously under the conditions of use without exce...

The modern word for plumber is derived from the Latin word for - ANSWER-A person who works with lead LEED applies to all areas of the profession, except - ANSWER-Renovation Water that comes from laundry and bathtubs and reused in known as - ANSWER-Graywater Suggested national plumbing standards are called - ANSWER-Model codes You are offered a job by another contractor before you have fulfilled your current obligations. The professional response is to - ANSWER-Ask the contractor to w...

1. Takeoffs of conduit are categorized into ______. - ANSWER ☑☑Power distribution, branch lighting, and branch power 2. Raceways are taken off per _____. Fittings required to make turns and extensions are taking off per _____. - ANSWER ☑☑Linear foot, each 3. All wires and conductors are taken off per _____. - ANSWER ☑☑Linear foot 4. All fittings, devices and boxes are taken off per _____. - ANSWER ☑☑Each Item 5. Permits and fees for tie-ins may be listed at lump s...

C-10 ELECTRICAL PART 1 EXAM 2024/ ACTUAL EXAM WITH COMPLETE VERIFIED SOLUTIONS ALREADY GRADED A+ 1. Takeoffs of conduit are categorized into . - answer Power distribution, branch lighting, and branch power 2. Raceways are taken off per . Fittings required to make turns and extensions are taking off per . - answer Linear foot, each

Calfornia C10 Electrical Exam Set Test Questions And Verified Correct Answers 1. Takeoffs of conduit are categorized into ______. - ANSWER : Power distribution, branch lighting, and branch power 2. Raceways are taken off per _____. Fittings required to make turns and extensions are taking off per _____. - ANSWER : Linear foot, each 3. All wires and conductors are taken off per _____. - ANSWER : Linear foot 4. All fittings, devices and boxes are taken off per _____. - ANSWER : ...

Journeyman Electrician Questions and Answers with Verified Solutions For other than one-and two-family dwellings, when building a new electrical service, at least one (1) 125-volt, single-phase, 15- or 20-ampere-rated receptacle outlet shall be located within at LEAST _____ of the electrical service equipment? 50 feet The ampacity of a conductor is defined by the NEC to be the maximum current, in amperes, a conductor can carry continuously under the conditions of use without exceeding ______? ...

NHIE Electrical Exam Questions with 100% Correct Answers Updated What does code say about bends in NM conduit? - Answer- No sharp bends; max 5x cable diameter. What must you do if you run more than 2 wires through the same fireblocked wood framing hole? - Answer- Wires must be derated. What is UF wire? - Answer- Underground feeder cable. What are the rules when using UF cable on the interior of a home? - Answer- Same as NM wiring. When must UF cable be protected? - Answer- Cable em...

EOPAOSHA (Occupational Safety and Health Administration) - correct answer The ____________ is the federal government agency established to ensure a safe and healthy environment in the workplace. Job-related learning acquired while working is known as ____________. - correct answer On-the-job learning (OJL) The main panelboard enclosure would probably be installed in the ____________ stage. - correct answer Rough-in The ____________ connects the serving utility to the premises wiring sys...

Michigan Mechanical Code 2024 with Verified Solutions A mechanical joint is not ________ . Welded Any combination of outdoor and transfer air intended to replace exhaust air and exfiltration is ___________. make up air A tube or conduit utilized for conveying air is a ___________ . duct A permanent mechanical joint incorporating an elastomeric seal and corrosion resistant grip ring is a __________ . press joint Plastic pipe, fittings and components shall be ___________ as con...

A conduit fitting that has been evaluated and listed to prevent the ingress of cutting fluids is marked ? . - Answer a. liquidtight Conduit fittings marked "raintight" or "wet locations" are automatically considered "liquidtight." - Answer False Which NEC articles pertain to liquidtight flexible metal conduit and liquidtight flexible nonmetallic conduit, respectively? - Answer b. Articles 350 and 356 Liquidtight conduit fittings are required to be listed. - Answer True...