Cwb level 1 - Samenvattingen en Aantekeningen

CWB WELDING INSPECTOR LEVEL 1 EXAM NEWEST ACTUAL EXAM COMPLETE 200 QUESTIONS AND CORRECT DETAILED ANSWERS (VERIFIED ANSWERS)

CWB Level 1 Exam Prep (Latest 2024 / 2025 Update) Questions and Verified Answers | 100% Correct | Grade A Q: Why must European drawings be studied carefully before fabricating parts? Answer: The drawings may employ the use of first angle projection Q: How many principal views are there in an orthographic projection? Answer: 6 Q: What is the angle of inclination most commonly used on an isometric drawing? Answer: 45degree Q: Which lines appear thicker on an engineering drawing? Answer: object lin...

CWB Level 1 Exam Prep (Latest 2023/ 2024 Update) Questions and Verified Answers| 100% Correct| Grade A Q: Why must European drawings be studied carefully before fabricating parts? Answer: The drawings may employ the use of first angle projection Q: How many principal views are there in an orthographic projection? Answer: 6 Q: What is the angle of inclination most commonly used on an isometric drawing? Answer: 45degree Q: Which lines appear thicker on an engineeri...

CWB Welding Inspector Level 3 Exam Prep (Latest 2023/ 2024 Update) Questions and Verified Answers| All Modules Covered| 100% Correct| Grade A Q: Fluxes that can dissolve the oxides on Al are ............ Answer: Halide compounds ( Fluorine, chlorine, Bromine etc.) Q: Chlorine gas from a Chloride flux in presence of an arc can create poisonous gas called .......... Answer: Phosgene (COCL2) or Mustard gas produced by the reaction of chlorine and carbon monoxide in the prese...

CWB Welding Inspector Level 2 Exam Prep (Latest 2024 / 2025 Update) Questions and Verified Answers | All Modules Covered | 100% Correct | Grade A Q: In an isometric drawing, the lines (for width, length and depth) are inclined at an angle of how many degrees? Answer: 30° Q: What are the maximum number of views in an orthographic drawing? Answer: 6 Q: What are the two general classes of picture drawings? Answer: Perspective and Isometric Q: What are the 5 basic joints? Answer: 1) Butt 2) Corner ...

CWB LEVEL 2 STUDY QUESTIONS REV 1

CWB LEVEL II 9 (KEY REVIEW POINTS FROM MODULES 1 THROUGH 22) NEWEST ACTUAL EXAM COMPLETE 200+ QUESTIONS AND CORRECT DETAILED ANSWERS & RATIONALES. Terms in this set (203) What is the term used to describe the following condition of lost corrosion resistance? "When certain stainless steels are heated between 500-850° C, carbides form at the grain boundaries and cause a local depletion of chromium." (A) Oxidization (B) Increased toughness(C) Solution heat treatment (D) Sensitizat...

Level 1 - Chapter 3: CWB Welding Inspector 2025|Actual Exam Set Questions And Verified Answers (Correct solutions) | Get It 100% Accurate!!

CWB Level 1, Mod 4 - Welding Processes & High current, low voltage - correct answer Describe the current and voltage of a welding arc 30% arc heat at the electrode. 70% arc heat at the work. - correct answer What is the percentage of arc heat at the electrode and at the work when using the GTAW process with current set to DCEN? 15 degrees using a push technique - correct answer What travel angle and technique should be used with MCAW for a flat profile and good penetration? They are cla...

CWB Welding Inspector Level 1 Exam (Latest 2023/ 2024 Update) Questions and Verified Answers| 100% Correct| Grade A Q: From the welding problems identified below which one of the five does not fit the pattern established by the other four? a) Insufficient throat. b) Incorrect bevel angle. c) Loss of shielding gas. d) Improper fit up. e) Use of wrong consumable. Answer: a) Insufficient throat. Q: A 10 mm fillet weld has a nominal: a) Throat dimension of 10 mm. b) Area of ...