Gage length - Study guides, Class notes & Summaries

FRA Tier 2 Exam Questions With Verified And Updated Solutions. What is 213.1 - answerIt states that the FRA standards are the minimum requirements for railroad track. It also states that just because one aspect may meet standard, a combination may cause a defect. Also it does not restrict the railroad from adopting stricter standards What is 213.5 (a) - answerStates that the owner of excepted track must (do one of the following) 1) Bring the Track into compliance 2) Halt operations over ...

An attached garage shall be separated from all habitable rooms above the garage with not less than 5/8 of an inch gypsum board A structure that is intended for swimming or recreational bathing is considered to be a swimming pool if it contains water over 24 inches What type of fastener do you use to install cabinets? Truss head wood screws The process of preparing sand underneath a concrete slab requires sand to be Compacted Habitable space in a basement shall hav...

0.020" thick aluminum is approximately: - 24 gage 0.020" thick copper approximately equals: - 24 gage, B&S A 10' length of stainless steel will expand _______ with a temperature increase of 100*F - 1/8" A fire extinguisher must be tested every: - Year A railing is required on work surfaces _______ or higher from the ground. - 7 1/2 ft A roof is considered to be low-pitched when its slope is: - 3:12 or less A roof with a slope of 8:12 is considered what pitch? - 1/3 pitch A roofing con...

NOCTI Electrical Questions and Answers Already Passed In general a beginning tradesperson with little or no experience in the electrical field is known as a/an apprentice The proper angle for setting up a ladder is to place its base a/an___________ of the working length of the ladder from the wall or other vertical surface. quarter A __________ fire extinguisher should be used on an electrical fire. Class C A person with a serious electrical injury should be moved only if they are in immedia...

C-39 Roofing Trade Practice Test 1 Questions with Answers Flat seam roofs of slight pitch should be divided by expansion battens into sections not exceeding: - Answer-30 ft square Before installing a flat seam roof, a wood deck should be covered with: - Answer-30 lb felt In the flat seam roofing method, the roof is covered by plans made from: - Answer-20" x 28" sheets What is the minimum gage copper recommended for flat seam roofs? - Answer-16 oz Batten seam roof are not recommen...

ACI Concrete Field Testing Technician Grade 1 Study Guide Latest Update Rated A+ ASTM C31 / C31M-06 Standard Practice for Making, Curing, Protecting & Transporting Test Specimens in the Field Conditions. ASTM C1064 /C1064M-05 Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete ASTM C172 -07 Standard Practice For Sampling Freshly Mixed Concrete From Different Containers Used In The Production or Transportation Of Concrete. ASTM C143 / C143M-05a Stand...

QMED - OILER EXAM PREP If a bolt or stud were to break off flush at the surface, how do you remove it - Answer- drill a hole in the center of the stud The number of screw threads per inch for Standard National Coarse 1/2 bolt is - Answer- 13 If a matching nut and bolt have class 4 or no. 4 fit they will - Answer- be hard to turn by hand but easy with a wrench what basic dimensions are used in describing bolts - Answer- diameter, length, and number of threads per inch The letters NC...

Which inspection device preforms go/no-go gaging? Plug gage What level of device sensitivity is required to measure a dimension of 0.365±.002 inches? The device should be accurate to: 0.0005 inches What production activity requires workers to compare part dimensions to desired specifications? Inspection How often do frequently-used instruments need calibration? Once a year Which of the following is true about gage blocks? Gage blocks: Can be combined to produce almost any standard length

ASNT VT Theory Questions (Level II) Answered Correctly To Pass!! Localized reduction in an area of a bolt that is under overload conditions is referred to as: a. sizing b. necking down c. erosion d. elongation b The least common location for fastener failure is: a. in the head to shank fillet b. throughout the first thread inside the nut on threaded fasteners c. in the mid grip d. at the transition from the thread to the shank c Discontinuities that are produced during the hot...

ASNT VT Theory Questions (Level II) Answered Correctly To Pass!! Localized reduction in an area of a bolt that is under overload conditions is referred to as: a. sizing b. necking down c. erosion d. elongation b The least common location for fastener failure is: a. in the head to shank fillet b. throughout the first thread inside the nut on threaded fasteners c. in the mid grip d. at the transition from the thread to the shank c Discontinuities that are produced during the hot...