Heat anticipator Study guides, Class notes & Summaries

NATE Gas Heating Exam Verified Questions and answers 2023 Latest Update Since 1992, the United States Department of Energy has required that all furnaces sold and installed from that date on must have an AFUE of no less than: A: 70% B: 75% C: 78% D: 80% - correct answer C: 78% Many pre-1992 furnaces have efficiencies around . A: 10% B: 40% C: 60% D: 80% - correct answer C: 60% Today, furnaces with AFUE ratings greater than are available. A: 85% B: 90% C: 100% D: 110% - correct ...

What are the 3 funtions of an Oil Burner nozzle? - Answer- Atomize, Meter, Patter. What are the 2 voltage circuits of a primary control? - Answer- Line & Low. What is the function of a fuse? - Answer- Protect circuit. What is the High Limit cut out? - Answer- Max safe Temp or Pressure setting. What is the High Limit cut in? - Answer- Cut out minus Differential. What is the "Max" Lockout time for a burner with a 3 GPH Flow Rate? - Answer- 45 Seconds. What is the minimum stack ...

G2 Exam Quiz Bank (2024/ 2025 Update) Questions and Verified Answers| 100% Correct| Grade A Q: The STACK EFFECT in a water heater is usually caused by Answer: Short draws of water from the heater Q: A 120v power supply for a residential electrical circuit is taken from the Answer: - Load side of one branch circuit breaker and a neutral lug Q: The minimum allowable distance to be maintained from a 50,000 btuh water heater flue outlet gas regulator Answer: 3' ...

Gas Technician G2 Exam (2024/ 2025) Questions and Verified Answers| 100% Correct| Grade A Q: On an Electrical Schematic, all operating controls are drawn: Answer: Normally Open Q: As the length of a Conductor Increases, the Voltage Drop along the Conductor: Answer: Increases Q: When a new appliance is to be installed in a typical residential basement and the Supply Wiring to it is concealed, which of the following types of wire is acceptable, and most cost effectiv...

1. A gas furnace is to be installed in a garage. The burners and ignition sources must be located ______ above the floor. A: 6 inches B: 12 inches C: 18 inches D: 24 inches - Answer-C: 18 inches 2. A good description of how hi-metai fan switch operates the blower motor on a gas furnace is: A: temperature on - time off. B: temperature on - time on. C: temperature on- temperature off. D: time on - time off. - Answer-C: temperature on- temperature off 3. Redundant gas valves used on gas ...

senible heat Ans: Heat that can be measured by a thermometer latent heat Ans: heat required to create a phase change without a change in temperature. Phychrometric Ans: The study of air and its properties What is enthapy? Ans: The total measure of heat content in the air and is made up of sensible and latent heat measured in BTU per pound of air Cooling anticipator is wired how? Ans: Parallel with temp control How is heating anticipator wired? Ans: In series with t-stat control Net...

HVAC NATE Heat Pump Exam Questions With Correct Answers Updated 2024/2025 (Graded A+) What is the primary purpose of using flux when soldering copper or brass parts? -Ans Prevent Oxidation The water that results from a defrost cycle of an air to air heat pump(runoff) must? -Ans Drain off and away from the outdoor coil. Why must the runoff be drained off and away from the outdoor coil? -AnsExcessive ice can build up on the bottom of the coil and can reduce capacity. What is the component th...

NATE Heat Pump Exam Questions With Correct Answers Updated 2024/2025 (VERIFIED A+) The water that results from a defrost cycle of an air to air heat pump(runoff) must? -Ans Drain off and away from the outdoor coil. Why must the runoff be drained off and away from the outdoor coil? -AnsExcessive ice can build up on the bottom of the coil and can reduce capacity. What is the component that reduces sound transmission and prevents water leaks of a package heat pump installed on a roof? -Ans Cur...

HVAC NATE Heat Pump /171 Questions with Correct Answers Assured A+. On an R-22 system, line diameters and lengths are typically specified for a vapor pressure drop that does not exceed what? -Ans 6-7PSI or 6F What is the primary purpose of using flux when soldering copper or brass parts? -Ans Prevent Oxidation The water that results from a defrost cycle of an air to air heat pump(runoff) must? -Ans Drain off and away from the outdoor coil. Why must the runoff be drained off and away from ...

HVAC NATE Heat Pump Exam Questions and Answers 100% Pass On an R-22 system, line diameters and lengths are typically specified for a vapor pressure drop that does not exceed what? -Answer-6-7PSI or 6F What is the primary purpose of using flux when soldering copper or brass parts? - Answer-Prevent Oxidation The water that results from a defrost cycle of an air to air heat pump(runoff) must? - Answer-Drain off and away from the outdoor coil. Why must the runoff be drained off and away from...