Hexagonal nut - Study guides, Class notes & Summaries

Module 0103-15 Introductions to hand tools Questions and Answers 100% Pass Another name for a machinist's hammer is A. Ball-peen hammer B. Claw hammer C. Veneer hammer D. Sledgehammer - Answer- A. Ball-peen hammer A heavy-duty tool used to drive posts or other large stakes is a A. Mallet B. Sledgehammer C. Bell-faced hammer D. Ball-peen hammer - Answer- B. Sledgehammer The proper angle for the edges of a cold chisel is A. 90 degrees B. 60 degrees C. 45 degrees D. 30 degrees - Ans...

C 10 Electrical Exam Part V & VI & VII Exam Solved Questions With Revised Correct Detailed Answers Brand New Version !! 1. Which of the following is an acceptable marking method for the grounding conductor on a grounding-type receptacle? A) A white-colored round-headed terminal. B) A tag with 1/4-inch high letters. C) An orange dot. d) D) A green-colored hexagonal headed or shaped terminal screw or nut. - ANSWER NEC Section Section 406.9(B) permits Answer D as one...

The alteration between object markers and barriers reflectors is to be what spacing? A. 50' B. 40' C. 30' D. 25' - ...ANSWER...25' Glare screen shall be designed using a _____ degree cut off angle of the paddle based on the tangent? A. 45 degree B. 30 degree C. 20 degree D. 10 degree - ...ANSWER...20 degree What is the portable barrier wall minimum flare rate for 65 mph zone? A. 12:1 B. 65:1 C. 19:1 D. 8:1 - ...ANSWER...19:1 What type of nut goes on hook and lo...

ACRP Chapter 6 Test Questions with All Correct Answers All of the following are examples of plastic fasteners EXCEPT: A. Push pin B. Reusable rivet C. Clips D. All are examples of plastic fasteners - Answer-D. All are examples of plastic fasteners What can be applied to prevent bolts from becoming fused or cold welded with any connected components? A. Motor oil B. Anti-seize lubricant C. Grease D. Liquid thread lock - Answer-B. Anti-seize lubricant An internal snap ring is remo...

Is a shadow vehicle used in all traffic zones? A. True B. False - False The shadow vehicle is occupied whenever workers are in the work area. A. True B. False - False What class one light is the shadow vehicle equipped with? A. Flashing Yellow Light B. Oscillating Yellow Light C. Yellow Strobe Light D. All of the above - All of the above When may cones be substituted for drums? A. Daytime traffic control minimum height 18" B. Daytime traffic control minimum height 28" C. Dayt...

What is the minimum rating required for a receptacle? - Answer 15 A A single receptacle connected to a 30-ampere branch circuit must generally have a rating not less than ------ amperes. - Answer 30 Amps If 15- and 20- ampere duplex receptacles are not marked with "CO/ALR" they are suitable for use with -------. - Answer Copper and copper-clad aluminum conductors only. Duplex receptacles are required to be installed so that the equipment grounding contact is oriented in what ...

Another name for a machinist hammer is a - Answer-Ball-peen hammer A heavy duty tool used to drive post or other large stakes is a - Answer-Sledge hammer The proper angle for the edge of a cold chisel - Answer-60 degrees A Reed and Prince screw comes to a relatively sharp point at - Answer-the base of it's drive socket When an object is plumb it is - Answer-perfectly vertical One situation that can make a measurement with a laser inaccurate is - Answer-Measuring to a highly refle...

NCCER MODULE 3 REVIEW EXAM QUESTIONS AND 100% COMPLETE ANSWERS WITH RATIONALES VERIFIED AND WELL EXPLAINED BY EXPERTS ALREADY PASSED!!!!!!GRADED A+ LATEST UPDATE 2024 WITH 100% GUARANTEED SUCCESS AFTER DOWNLOAD (ALL YOU NEED TO PASS YOUR EXAMS Ball-peen hammer Another name for a machinist's hammer is _____. Sledgehammer A heavy-duty tool used to drive posts or other large stakes is a ________ 60 degrees The proper angle for the edge of a cold chisel is ________. Robertson The type of screw ...

Module 0103-15 Introductions to hand tools Questions and Answers 100% Pass Another name for a machinist's hammer is A. Ball-peen hammer B. Claw hammer C. Veneer hammer D. Sledgehammer - Answer- A. Ball-peen hammer A heavy-duty tool used to drive posts or other large stakes is a A. Mallet B. Sledgehammer C. Bell-faced hammer D. Ball-peen hammer - Answer- B. Sledgehammer The proper angle for the edges of a cold chisel is A. 90 degrees B. 60 degrees C. 45 degrees D. 30 degrees - An...

NCCER Module 3 (Hand Tools) | Questions and Verified Solutions Latest Update what is another name for a machinist hammer? - Answer -Ball-peen hammer a heavy duty tool used to drive posts or other large stakes is called a? - Answer -Sledgehammer what is the proper angle for the edge of a cold chisel? - Answer -60- degrees what types of screw comes to a relative sharp point at the base of its drive socket? - Answer -Reed and Prince how many sides does a Hexagonal shape have? - Answer -six s...