Lockout equipment - Study guides, Class notes & Summaries

Place a check next to the most frequent sided OSHA violation .................. A)lockout tag out B) fall protection C) electrical wiring D) Machine guarding - ANSWER-B) fall protection Circle the key elements that are essential to recognizing hazard and reducing and or eliminating work place hazards................ A) management commitment and employee involvement B) worksite analysis C) hazard prevention and control D) safety and health training - ANSWER-B) worksite analysis ...

SACA Certification Exam C-101 || Questions & Answers (Graded A+) SACA Certification Exam C-101 || Questions & Answers (Graded A+) What are the 5 steps of electrical Lockout/tagout - ANSWER - 1. Shut down the equipment 2.Connect Hasp 3. Attach Lock 4. Add Tag 5. Test Start Equipment Which of the following is a common cause of workplace death? - ANSWER - Falls The process of identifying potential hazards in the workplace is known as a __________. - ANSWER - Hazard assessment An in...

IEC lesson 106 HW Questions and Answers Graded A+ A failure of the electrical system can cause damage to ___. -equipment -conductors -property A failure of the electrical system can cause fire damage to property. true A worker may use any sturdy lock to apply a lockout. false Applying locks or tags in the right places de-energizes the equipment. false Area of a circle PI * (radius)^2 Area of a rectangle Length of longer side * Length of shorter side Area of a square L...

As per CAN/ULC S801, on an electrical distribution overhead utility line circuit, verification of voltage absence can be achieved by: - Using an approved voltage detector. Isolation and tagging (no locks) is acceptable on an overhead distribution circuit under some of the following conditions, EXCEPT for: - The isolation can be operated from the ground directly at the base of a structure. Isolation and tagging (no locks) is acceptable for an overhead distribution circuit under some of the ...

When connecting a 3-phase motor the three lines (T1,T2 and T3) are usually connected to __________. - L1, L2, and L3 Electricians use __________ to prevent damage to electrical wiring running to the machine. - rigid and flexible conduit When the wire or foil strip inside a fuse melts, the fuse is said to be __________. - blown The difference between a fuse and a circuit breaker is __________. - circuit breakers can be reset and used again The amount two electrical...

If you inhale phenolic fumes what would happen to you? Trouble breathing A _________ fire extinguisher should be used on an electrical fire. Class C What does OSHA stand for? Occupational Safety & Health Administration This type of drawing represents a three-dimensional object using several two-dimensional views of the object. Orthographic What are linear dimensions usually expressed in? Decimal or Fractional Units What does a filled triangle represent in a fluid po...

OSHA Basic Orientation Plus Test | 50 Questions with 100% Correct Answers | Verified | Updated 2023 What is the most frequently cited OSHA violation? - Correct Answer Fall Protection What key elements are essential to recognizing hazards and reducing or eliminating workplace hazards? - Correct Answer Management commitment and employee involvement You are encouraged to ask your coworkers/supervisor for information whenever you have a problem or are in doubt about what to do on a job? - Cor...

The CFT was designed to evaluate which of the following? - Correct answer-Answer: Stamina, Agility, Strength Which equipment is required for a CFT? - Correct answer-Calibrated scale, dummy grenades, and measuring tape As a CFT monitor, you must assist in the risk management(RM) process for the CFT. Which of the following describes the RM process steps? - Correct answer-Identifying hazards, assessing risks, determining which risks are most important, implementing controls, and supervising ...

under strict safety guidelines, which of the following should be used to discharge capacitors before working on de-energized circuits. - safety shorting probe for safety, assume that any facility constructed before 1980 has? - asbestos with of the following is the threshold at which a power source is considered high voltage in the context of safety? - over 600V- 600Volts insulated gloves must be inspected by the user? - always and field checked the normal beating of a heart can be upset by...

OSHA Basic Orientation plus Exam - Questions with verified answers Required when you are exposed to noise over 85 decibels Hearing Protection Hearing Protection Device Ear Plugs Hearing Protection Device Ear muffs Has little or no training in identifying electrical hazards Non-Qualified Person (electrical) Has received training in and has proven skills and knowledge in the construction and operation of electric equipment Qualified Person (electrical) Occurs when a flashover of electric current ...