Oil burner 2 - Study guides, Class notes & Summaries

What is a general requirement of the location of the installation of a boiler? - ANSWERSAdequate clearance from combustile construction What temperature must the materials remain under during combustion? - ANSWERS170 degrees What is a requirement for the access of the boiler? - ANSWERSAccess for operation and maintenance must not be hazardous What is required upon installation to operate a boiler? - ANSWERSInspection and test resulting in equipment use permit from commissioner How of...

P-99 / Low PSI Oil Burner Operator Questions and Answers 100% Solved All heating, combustion, and cooking equipment shall be provided with insulation or the building construction shall be fire protected, so that during operation the surface of combustible construction materials will not be raised to a temperature higher than ____. 170 ̊F Acceptance tests: Boilers shall not be placed in operation upon completion of construction until they have been ____ and an equipment use permit has ...

What is the first thing a tech should do when arriving at a no combustion call? - Answer- Ask how many times the customer reset the unit. What is the best long term solution for preventing a clogged nozzle? - Answer- -Remove any underground storage tanks. -Install a quality oil filter. -Cut the suction line 10" above the tank outlet to prevent sludge. Hot water and steam valves are interchangeable. - Answer- False When in the presence of a flame, a cad cell normally reads.. - Answe...

G2 Final Exam Questions and answers with 100% Complete Solutions | verified &updated 2024 What is the min. diameter for a leak test gauge? - 3" Amp meter can read? - Conductor magnetic field. What would the primary voltage to the furnace be? - 120/1/60 What is the function of the intermittent pilot? - Stays on during the main burner operation. What is the millivolt power output of a closed circuit thermocouple? - 10 - 15 mv dc A pilot with a lazy yellow flame indicates? - Orifice is too l...

What are the 3 funtions of an Oil Burner nozzle? - Answer- Atomize, Meter, Patter. What are the 2 voltage circuits of a primary control? - Answer- Line & Low. What is the function of a fuse? - Answer- Protect circuit. What is the High Limit cut out? - Answer- Max safe Temp or Pressure setting. What is the High Limit cut in? - Answer- Cut out minus Differential. What is the "Max" Lockout time for a burner with a 3 GPH Flow Rate? - Answer- 45 Seconds. What is the minimum stack ...

How often shall fuel-oil storage tanks and piping be inspected for leaks? - ANSWERSWeekly. For what two purposes is fuel-oil generally used in buildings? - ANSWERS(1) Emergency generators. (2) Heat. How often shall fuel-oil storage tanks have their float switches tested? - ANSWERSWeekly. Fuel-oil transfer shall be conducted under the ____ supervision of a P-98 COF holder. - ANSWERSGeneral. Fuel-oil system testing shall be conducted under the ____ supervision of a P-98 COF holder. ...

COF P-98 PRACTISE EXAM / 100 QUESTIONS AND VERIFIED ANSWERS 2023/2024 / ALL CORRECT. COF P-98 Practice test 2023 1. The person supervising the Fuel-Oil transfer in the building from one floor to another must hold what type of certificate of fitness: P-98 Certificate of Fitness 2. In designing the fuel-Oil transfer system, such as diesel #2 oil from the lowest floor to the floor above the tank level, the following factors must be considered:: - Maximum inlet suction an flow-rate - Desi...

What is a general requirement of the location of the installation of a boiler? - ANSWERSAdequate clearance from combustile construction What temperature must the materials remain under during combustion? - ANSWERS170 degrees What is a requirement for the access of the boiler? - ANSWERSAccess for operation and maintenance must not be hazardous What is required upon installation to operate a boiler? - ANSWERSInspection and test resulting in equipment use permit from commissioner How of...