Shutdown procedure - Study guides, Class notes & Summaries

LRM4801 Assignment 13 Answers (Due date: 10 January 2024) APPENDIX A: ASSESSMENT 13 Please Note: This written Assessment must be submitted in PDF format via myUnisa. Instructions on how to submit the Assessment are provided in section 6 of this document. You are expected to meet particular requirements relating to the layout and technical presentation of Assessments: • The cover page or first page of your document should display information such as the module code, Assessment num...

Z-51 Written Exam Questions and Complete Solutions In a steam turbine, what is the function of a Kingsbury thrust bearing? A) Maintain first stage steam pressure. B) Compensate for coupling misalignment. C) Adjust shaft torque at start up. D) Maintain axial positioning of the rotor shaft. - Answer: D) Maintain axial positioning of the rotor shaft. The ratio of actual pressure of water pressure in the atmosphere to the saturated pressure of given temperature is A) partial pressure....

Several days before shutting down a boiler, increase the rate of continuous blowdown, and increase the: Select one: a. operating pressure to check safety interlocks b. frequency of bottom blowdown c. firing to stimulate water circulation d. frequency of equipment checks for any sign of leaks e. start running the boiler on low fire b Prior to shutting down a hot water boiler: Select one: a. it is important to check for leaks b. pop open the safety valve c. the operator m...

Before starting engines - WWC Rotor tie downs removed While fully restrained ensure that you are able to reach all switches and emergency controls Do not grasp the foam while adjusting your seat Circuit breakers and switches set - N If IMC is expected STBY switch must be tested for 5 seconds. BATT GOOD will appear for 5 seconds to ensure 30 Minutes of ESIS battery is available. Batt No1& 2 - N Two beeping tones will be heard for ICS check AU CONT Switch on - NN APU f...

How long of a cooling period do you need before shutting down? 2 min What do you need to ensure is off and how far in advance of shutdown? Cowl anti-ice off 30-60 sec before shutdown Previous Play Next Rewind 10 seconds Move forward 10 seconds Unmute 0:00 / 0:15 Full screen Brainpower Read More What parameter do you need to monitor after engine shutdown? ITT- cannot rise above 350 and rising rapidly- start motoring cycle of engine What needs to remain on aft...

HESI FUNDAMENTALS EXAM VERSION 3 (V3) (2023/2024) All 55 Questions HESI FUNDAMENTALS EXAM 1) During the initial physical assessment of a newly admitted client with a pressure ulcer, a LPN observes that the client's skin is dry and scaly. The nurse applies emollients and reinforces the dressing on the pressure ulcer. Legally, were the nurse's actions adequate? A The nurse also should have instituted a plan to increase activity. B The nurse provided supportive nursing care ...

How do you use a level? - Answer-Adjust until bubble is centered. What is Lockout Tagout? - Answer-A safety procedure to isolate energy sources during maintenance. What are the steps involved in Lockout Tagout? - Answer-Preparation, Notification, Shutdown, Verification, Maintenance/Repair, Removal. What is the purpose of Lockout Tagout? - Answer-To protect workers from unexpected equipment startup or hazardous energy release. What are the potential energy sources that need to be isol...

OSHA Basic Orientation plus Exam - Questions with verified answers Required when you are exposed to noise over 85 decibels Hearing Protection Hearing Protection Device Ear Plugs Hearing Protection Device Ear muffs Has little or no training in identifying electrical hazards Non-Qualified Person (electrical) Has received training in and has proven skills and knowledge in the construction and operation of electric equipment Qualified Person (electrical) Occurs when a flashover of electric current ...

When using a dynamic schedule and the energy profile in an hour is >250 MW and the actual hourly integration deviates from the hourly energy profile by ____ the tag must be modified. A. 100 MW B. 10% C. 50 MW D. 25% B. 10% Dry steam plants, flash steam plants, and binary cycle power plants are the three main types of what kind of generating plant? A. Nuclear generators B. Combustion turbine generators C. Geothermal generators D. Hydroelectric generators C. Geothermal generators...

CHSP 26 EXAM QUESTIONS AND REVISED ANSWERS ALL CORRECT What contributes most to accidents, incidents, and near miss events? - Answer inadequate management What describes a surgical fire procedure required by NFPA 99? - Answer Develop procedures for alarm activation, evacuation, and equipment shutdown What entity developed the Universal Protocol to reduce wrong site surgeries? - Answer Joint Commission What hazardous substance would lab research personnel use to make biochemical sep...

CABIN ALT Msg or Emergency Descent Procedure correct answers 1. Oxygen Masks.....Don and 100% 2. Crew Communications......Establish During Landing - Excessive Asymmetry or Loss of Braking correct answers Wheel brakes....release momentarily Anti-skid....off Wheel brakes....re-apply as required Engine Indications correct answers Red-Maximum and minimum limitations Amber-caution range Green-normal operating range Engine Stabilization correct answers Prior to takeoff: engines must be r...