Technician a says Study guides, Class notes & Summaries

a lifting pad must be in place to lift a BMW vehicle, T or F? - correct answer True Under which section in TIS is the User Manual for the DEUTRONIC battery charger located? - correct answer Tools and Equipment Regarding BMW instrument cluster test function. Tech A states the cluster can be unlocked, and a test function can be used to display fuel level reading in liters. Tech B states current BMW instrument clusters are unlocked by using su...

The reading on the micrometer shown above is ? - Answer-6.5mm What causes brake pulsation? - Answer-Variation thickness of brake rotor A wheel bearing can cause a DSC fault. True or False? - Answer-True 3 wheel shows 24 miles and 1 is 23, what can be the cause? - Answer-Bad wheel bearing In a parallel circuit it shows three bulbs that aren't operating. What can be the cause ? - Answer-Open from Y TO Z An XDrive vehicle equipped with a transfer case makes a clunking noise during ac...

1. The truck with the air suspension system shown above leans to the right. Technician A says that valveX could be the cause. Technician B says that valve Y could be the cause. Who is right? A. Technician A only B. Technician B only C. Both A and B D. Neither A or B - Answer 1. The correct answer is C, both technicians are right. Height control valves can fail in either direction-that is, by controlling the height at too great a level or at too low a level. If the truck leans, the cause ...

Suspension and Steering Practice Test with Verified Solutions A vehicle has excessive body sway while cornering. Which of these is most likely to cause this condition. A. A binding ball joint. B. A warn idler arm. C. Warn control arm bushings. D. Warn stabilizer bar bushings D. Warn stabilizer bar bushings A vehicle with variable assist steering feels loose only at highway speeds. Technician A says this is likely caused by the vehicle speed sensor. Technician B says this could be ...

Whining - correct answer A tight timing belt makes what type of noise? plugged transmission breather filter - correct answer A RWD (rear wheel drive) transmission has a leaking output shaft seal on a vehicle with 25,000 miles on the odometer. The MOST likely cause for the leakage is: Burping - correct answer Of the following, when replacing a CV (constant velocity) joint or boot, what is the last step before clamping the boot? positive caster - correct answer Steering dampers can be used to...

PA APPRAISERS LICENSE EXAM 2024 NEWEST VERSION WITH 300+ ACTUAL EXAM QUESTIONS AND CORRECT VERIFIED ANSWERS/ 2024 PA APPRAISERS LICENSE REAL EXAM 2024 WITH ANSWERS (GUARANTEED A+) The auto appraiser considers the extent of damage, the size of the damaged area, and the appearance. Usually, if the repair cost exceeds ____ of the cost to replace the part, replacement is appropriate. - ANSWER-75% The identifying marks on a plastic part are so worn down they cannot be read. Therefore, the...

The recovery process on an R-12 or R-134a A/C System should continue until a stable vacuum is held by the system for: - ANSWER-2 minutes A recycled refrigerant container has been checked and found to be above the given pressure limit for the ambient temperature Technician A says that the refrigerant container should be placed in a cooler storage area before use Technician B says that the vapor in the container should be slowly vented into a refrigerant handling unit who's right - ANSWER...

ASE A4 practice test questions and answers 100% pass 2. A driver says that the front end of his car vibrates up and down while traveling at most road speeds. Tech A says that too much runout of the front wheels could be the cause. Tech B says that a static out of balance of the front wheels could be the cause. Who is right? A. Tech A only B. Tech B only C. Both A and B D. Neither A or B - Answer ️️ -C. Both Techs are right. Too much runout or static out of balance in the front wheels...

BOMA – HVAC QUESTIONS AND ANSWERS 100% PASS Two basic categories of chillers are the compression cycle and absorption The five requirements for comfort are proper temperature, humidity, filtration, and ventilation circulation The primary function of an expansion device is to produce a reduction in the pressure on the liquid refrigerant, regulate the flow of refrigerant into the evaporator, lower the boiling point of the refrigerant far enough below the temperature of the load to g...

SAE 609 Questions and Answers 100% Pass The recovery process on an R-12 or R-134a A/C System should continue until a stable vacuum is held by the system for: 2 minutes A recycled refrigerant container has been checked and found to be above the given pressure limit for the ambient temperature Technician A says that the refrigerant container should be placed in a cooler storage area before use Technician B says that the vapor in the container should be slowly vented into a refrigerant handling...