Virginia hic stuvia - Study guides, Class notes & Summaries

The MOST specific information about the size and location of windows would be found in a - ANSWER-Floor plan What direction does heat flow? - ANSWER-Hot to cold What are batter boards - ANSWER-stakes and ledger boards marking building lines What is the MAXIMUM distance between a ventilating opening in an under-floor space and each corner of the building? - ANSWER-3 feet What is NOT required in exterior nonbearing walls? - ANSWER-Load-bearing headers A lengthwise grain separation b...

The MINIMUN length drywall screw for installing 1/2 inch gypsum board to wood studs is - ANSWER-1 1/4 inches What is the MINIMUM breaking strength required of safety belt lanyards - ANSWER-5,400 pounds What is the MINIMUM clearance that combustible insulation MUST other heat-producing devices - ANSWER-1 inch What is the MAXIMUM flame spread index for insulation materials - ANSWER-25 The amount of water per sack of cement is what controls all EXCEPT - ANSWER-Wear resistance The esc...

What is directly affected by the surface and subsurface conditions of the building site? - ANSWER-Foundations - While the type and size of a structure will partly determine the type of foundation, the foundation itself is very much affected by the surface and subsurface conditions of the building site. What term is used to describe the act of removing air pockets from setting concrete? - ANSWER-Vibrating Concrete - Consolidation is a process that removes air pockets and forces the concrete in...

What is the MINIMUM breaking strength required of safety belt lanyards - ANSWER-5,400 pounds What is the MINIMUM clearance that combustible insulation MUST other heat-producing devices - ANSWER-1 inch What is the MAXIMUM flame spread index for insulation materials - ANSWER-25 The amount of water per sack of cement is what controls all EXCEPT - ANSWER-Wear resistance The escape device for a trench over 4 feet deep MUST be within a MAXIMUM of - ANSWER-25 feet of the worker What is t...

The MINIMUN length drywall screw for installing 1/2 inch gypsum board to wood studs is - ANSWER-1 1/4 inches What is the MINIMUM breaking strength required of safety belt lanyards - ANSWER-5,400 pounds What is the MINIMUM clearance that combustible insulation MUST other heat-producing devices - ANSWER-1 inch What is the MAXIMUM flame spread index for insulation materials - ANSWER-25 The amount of water per sack of cement is what controls all EXCEPT - ANSWER-Wear resistance The esc...

What is the MAXIMUM distance between a ventilating opening in an under-floor space and each corner of the building? - ANSWER 3 feet What is NOT required in exterior nonbearing walls? - ANSWER Load-bearing headers A lengthwise grain separation between or through the growth rings of lumber is called a - ANSWER Shake (c 326) The abbreviation "d" in "16d" means - ANSWER Penny Notches may not be located in the ____________ of a joist span - ANSWER Middle 1/3 How should boar...

The amount of water per sack of cement is what controls all EXCEPT - ANSWER Wear resistance The escape device for a trench over 4 feet deep MUST be within a MAXIMUM of - ANSWER 25 feet of the worker What is the correct sequence for installing a bi-fold door - ANSWER Top track, lower track, insert bottom pivot, insert upper pivot What is the MINIMUM height for a stairway handrail - ANSWER 34 inches How MUST rafters be framed to each other - ANSWER With rectangular ties The nailing ...

Anchor bolts should be spaced no more than __' apart and no more than __" from the ends of any plate section or wall corner. Each bolt must extend at least __" into the concrete. - ANSWER 6, 12, 7 In Southern Coastal areas, where should the vapor barrier be placed? - ANSWER The exterior of the wall. If butt joints occur when applying gypsum panels to wood and steel framing stagger and locate them as far from the ___ of walls and ceilings as possible. - ANSWER Center A minimum t...

The MINIMUN length drywall screw for installing 1/2 inch gypsum board to wood studs is - ANSWER 1 1/4 inches AnswerWhat is the MINIMUM breaking strength required of safety belt lanyards - ANSWER 5,400 pounds AnswerWhat is the MINIMUM clearance that combustible insulation MUST other heat-producing devices - ANSWER 1 inch AnswerWhat is the MAXIMUM flame spread index for insulation materials - ANSWER 25 AnswerThe amount of water per sack of cement is what controls all EXCEPT - ANSWER We...

The MOST specific information about the size and location of windows would be found in a - ANSWERFloor plan What direction does heat flow? - ANSWERHot to cold What are batter boards - ANSWERstakes and ledger boards marking building lines What is the MAXIMUM distance between a ventilating opening in an under-floor space and each corner of the building? - ANSWER3 feet What is NOT required in exterior nonbearing walls? - ANSWERLoad-bearing headers A lengthwise grain separation betwee...