ICC BOLTING 2024-2025 QUESTIONS WITH
100% CORRECT ANSWER
According to the IBC, the "blank" is to hire the special inspector. - CORRECT ANSWER
owner or owners agent. 2009 IBC Section 1704.1
According to the IBC, the "blank" is the responsible for the approval of a person's
qualifications to act as a special inspector. - CORRECT ANSWER code official. 2009
IBC, Section 1704.1
According to the IBC, discrepancy corrections are made known to the building official by:
- CORRECT ANSWER final report. 2009 IBC, Section1704.1.2
When is the code official to be made aware of a discrepancy found during a special
inspection? - CORRECT ANSWER If it is not corrected by the contractor. 2009 IBC,
Section 1704.1.2
According to the Model Program for Special Inspection, the special inspector is to
document work that is nonconforming: - CORRECT ANSWER In a written report -
Section II B 4 - Model Programs
According to the Model Program for Special Inspection, the special inspector is to
prepare written report of inspection: - CORRECT ANSWER After each inspection visit
- Section II B 5 - Model Programs
According to the Model Program for Special Inspection, which of the following items does
not need to be included in each inspection report? - CORRECT ANSWER Description
of discussions with the contractor - Section B 5 - Model Programs
,ICC BOLTING 2024-2025 QUESTIONS WITH
100% CORRECT ANSWER
According to the Specification for Structural Joints using high strength bolts, the nominal
diameter of standard bolt holes shall be how much larger than the nominal bolt
diameter? - CORRECT ANSWER 1/16 inch - Specification for Structural Joints Table
3.1
Discrepancies in the work shall be brought to the immediate attention of the "blank" for
corrective action. - CORRECT ANSWER the contractor - 2009 IBC, Section 1704.1.2.
The special inspector shall furnish inspection reports to the "blank" and to the "blank"? -
CORRECT ANSWER Building Official and Registered Design professional
The special inspector shall provide continuos inspection of: - CORRECT ANSWER
Single-pass fillet welds greater than 5/16 inch in size - 2099 IBC, Table 1704.3, Item 5.3
The special inspections required by this code are not required where the work is done on
the premise of a? - CORRECT ANSWER Approved fabricator - 2009 IBC, Section
1704.2.2
The special inspection of the steel fabrication process shall not be required where the
fabricator does not perform any? - CORRECT ANSWER heating operations - 2009
IBC, Section 1704.3, Exceptions # 1
, ICC BOLTING 2024-2025 QUESTIONS WITH
100% CORRECT ANSWER
According to the Specifications for Structural Steel Buildings, ASTM Standard "blank" is
to be used for the material test for steel sheets. - CORRECT ANSWER A568 -
Section A31, Specifications for Structural Steel Buildings
According to the Specifications for Structural Steel Buildings, the "blank" conducts the
material tests for identification of the structural steel. - CORRECT ANSWER
Fabricator or Testing Laboratory - Section A31, Specifications for Structural Steel
Buildings.
According to the Specifications for Structural Steel Buildings, which of the following steel
members are allowed to be unidentified steel? - CORRECT ANSWER Unimportant
members, where their physical properties and weldability would not affect the structure
strength - Section A31b, Specifications for Structural Steel Buildings
According to the Code of Standard Practice for Steel Buildings and Bridges, how is steel
of special material to be identified? - CORRECT ANSWER It is marked by the
supplier - Section 5.1.1, Code of Standard Practice for Steel Buildings and Bridges
According to the Code of Standard Practice for Steel Buildings and Bridges, how are
fabricators stock steel material identified? - CORRECT ANSWER Certified mill test
reports - Section 5.2.2 - Code of Standard Practice for Steel Buildings and Bridges
According to the Specification for Structural Steel Buildings, what ASTM Standard would
apply to a sample for structural steel pipe? - CORRECT ANSWER A53 - Section A31a
- Specification for Structural Steel Buildings
100% CORRECT ANSWER
According to the IBC, the "blank" is to hire the special inspector. - CORRECT ANSWER
owner or owners agent. 2009 IBC Section 1704.1
According to the IBC, the "blank" is the responsible for the approval of a person's
qualifications to act as a special inspector. - CORRECT ANSWER code official. 2009
IBC, Section 1704.1
According to the IBC, discrepancy corrections are made known to the building official by:
- CORRECT ANSWER final report. 2009 IBC, Section1704.1.2
When is the code official to be made aware of a discrepancy found during a special
inspection? - CORRECT ANSWER If it is not corrected by the contractor. 2009 IBC,
Section 1704.1.2
According to the Model Program for Special Inspection, the special inspector is to
document work that is nonconforming: - CORRECT ANSWER In a written report -
Section II B 4 - Model Programs
According to the Model Program for Special Inspection, the special inspector is to
prepare written report of inspection: - CORRECT ANSWER After each inspection visit
- Section II B 5 - Model Programs
According to the Model Program for Special Inspection, which of the following items does
not need to be included in each inspection report? - CORRECT ANSWER Description
of discussions with the contractor - Section B 5 - Model Programs
,ICC BOLTING 2024-2025 QUESTIONS WITH
100% CORRECT ANSWER
According to the Specification for Structural Joints using high strength bolts, the nominal
diameter of standard bolt holes shall be how much larger than the nominal bolt
diameter? - CORRECT ANSWER 1/16 inch - Specification for Structural Joints Table
3.1
Discrepancies in the work shall be brought to the immediate attention of the "blank" for
corrective action. - CORRECT ANSWER the contractor - 2009 IBC, Section 1704.1.2.
The special inspector shall furnish inspection reports to the "blank" and to the "blank"? -
CORRECT ANSWER Building Official and Registered Design professional
The special inspector shall provide continuos inspection of: - CORRECT ANSWER
Single-pass fillet welds greater than 5/16 inch in size - 2099 IBC, Table 1704.3, Item 5.3
The special inspections required by this code are not required where the work is done on
the premise of a? - CORRECT ANSWER Approved fabricator - 2009 IBC, Section
1704.2.2
The special inspection of the steel fabrication process shall not be required where the
fabricator does not perform any? - CORRECT ANSWER heating operations - 2009
IBC, Section 1704.3, Exceptions # 1
, ICC BOLTING 2024-2025 QUESTIONS WITH
100% CORRECT ANSWER
According to the Specifications for Structural Steel Buildings, ASTM Standard "blank" is
to be used for the material test for steel sheets. - CORRECT ANSWER A568 -
Section A31, Specifications for Structural Steel Buildings
According to the Specifications for Structural Steel Buildings, the "blank" conducts the
material tests for identification of the structural steel. - CORRECT ANSWER
Fabricator or Testing Laboratory - Section A31, Specifications for Structural Steel
Buildings.
According to the Specifications for Structural Steel Buildings, which of the following steel
members are allowed to be unidentified steel? - CORRECT ANSWER Unimportant
members, where their physical properties and weldability would not affect the structure
strength - Section A31b, Specifications for Structural Steel Buildings
According to the Code of Standard Practice for Steel Buildings and Bridges, how is steel
of special material to be identified? - CORRECT ANSWER It is marked by the
supplier - Section 5.1.1, Code of Standard Practice for Steel Buildings and Bridges
According to the Code of Standard Practice for Steel Buildings and Bridges, how are
fabricators stock steel material identified? - CORRECT ANSWER Certified mill test
reports - Section 5.2.2 - Code of Standard Practice for Steel Buildings and Bridges
According to the Specification for Structural Steel Buildings, what ASTM Standard would
apply to a sample for structural steel pipe? - CORRECT ANSWER A53 - Section A31a
- Specification for Structural Steel Buildings
