Network Pro Chapter 1-10 Test Questions with Answers All Correct
3 views 0 purchase
Course
Network Pro
Institution
Network Pro
Network Pro Chapter 1-10 Test Questions with Answers All Correct
Which of the following is a characteristic of static routing when compared to dynamic routing? - Answer-All routers must be manually updated on the router.
Network needs to support 1000 Mbps over ethernet. What cables must you rep...
Network Pro Chapter 1-10
Test Questions with
Answers All Correct
Which of the following is a characteristic of static routing when compared to dynamic
routing? - Answer-All routers must be manually updated on the router.
Network needs to support 1000 Mbps over ethernet. What cables must you replace? -
Answer-cat 3 cat4
Workstation -> Router Config Port. What cable? - Answer-Rollover
Which standard is typically used in a rollover cable? - Answer-RJ-232
Workstation -> Switch through regular port (not uplink) and switch doesn't support auto-
mdi. - Answer-Straight Through
Which connector is usually on one end of a rollover? - Answer-serial
You want to create a rollover cable that has an RJ-45 connector on both ends. How
should you connect the wires within the connectors? - Answer-Connect pin 1 to pin 8,
pin 2 to pin 7, pin 3 to pin 6, and pin 4 to pin 5
You want to connect the LAN port on a router to the uplink port on a switch. The switch
does not support auto-MDI. Which type of cable should you use? - Answer-Crossover
You need to transfer data from one laptop to another and would like to use an Ethernet
cable. You do not have a hub or a switch. Which type of cable should you use? -
Answer-Crossover
You have two switches that you need to connect using their uplink ports. The switches
do not support auto-MDI. Which type of cable should you use? - Answer-Crossover
You need to connect a workstation to a switch using a regular port on the switch (not an
uplink port). The switch does not support auto-MDI.
Which type of cable should you use? - Answer-Straight-through
,You have purchased a new router that you need to configure. You need to connect a
workstation to the router's console port to complete the configuration tasks.
Which type of cable would you most likely use? - Answer-Rollover
Which of the following connectors is typically used on one end of a rollover cable? -
Answer-Serial
Which of the following standards is typically used in a rollover cable? - Answer-RS-232
Using the exhibit to match the connector type on the left with the corresponding letter on
the right. - Answer-A- DB-25
B- DB-9
C- RJ45
D- RJ11
E- LC
F- BNC
G- F-Type
You want to create a rollover cable that has an RJ-45 connector on both ends. How
should you connect the wires within connectors? - Answer-Connect pin 1 to pin 8, pin 2
to pin 7, pin 3 to pin 6 and pin 4 to pin 5
You are implementing a SOHO network for a local business. The ISP has already
installed and connected a cable modem in the business.
The business has four computers that need to communicate with each other and the
Internet. The ISP's cable modem has only one RJ-45 port. You need to set up the
network with the following in mind: Spend as little money as possible. Do not purchase
unnecessary equipment. Computers need to have a gigabit connection to the network.
New devices should not require management or configuration - Answer-An unmanaged
switch and CAT5e cabling
You manage the two-location network shown in the exhibit. Workstations and servers at
each location connect to a patch panel using behind-the-wall wiring. The patch panel....
Drag the cable type on the left to the most appropriate network location on the right. -
Answer-Drop Cables
Cat6 straight-through UTP
Patch Cables
Cat6 straight-through UTP
Uplink Cables
Cat6 crossover UTP
WAN Cable
Single-mode fiber optic
You have a network connected using a physical bus topology. One of the cables
connecting a workstation to the bus breaks.
,Which of the following best describes what happens to network connections? - Answer-
No devices will be able to communicate
Which of the following can be performed by a TDR? (Select two.) - Answer-Identify the
location of a fault on a cable. & Measure the length of a cable.
You manage a network that uses 1000BaseT Ethernet. You find that one device
communicates on the network at only 100 Mbps.
Which tool should you use to test the drop cable and the connection to the network? -
Answer-Certifier
An access point that conforms to the IEEE 802.11b standard acts most closely to what
other networking device? - Answer-Hub
All of the 802.11 standards for the wireless networking support which type of
communication path sharing technology? - Answer-CSMA/CA
Uses a narrow frequency band and hops data signals in a predictable sequence -
Answer-FHHS
Breaks data into pieces and ends the pieces access multiple frequencies in a defined
range - Answer-DSSS
Breaks data into very small data streams in order to send the information across long
distances - Answer-OFDM
Which of the following is true of a wireless network SSID? - Answer-Groups wireless
devices together into the same logical network
Which wireless networking component is used to correct multiple APs together? -
Answer-DS
Which IEEE standard describes wireless communications? - Answer-802.11b
Which data transmutation rate is defined by the IEEE 802.11b wireless standard. -
Answer-11Mbps
You are designing a wireless network for a client. Your client needs the network to
support a data rate of at least 54Mbps. In addition, the client already has a wireless
telephone system installed that operates 2.4GHz. Which 802.11 stand will work best in
this situation? - Answer-802.11a
You are designing an update to your clients wireless network. The existing network
uses 802.11b. Due to budget, which 802.11 standard will work best. - Answer-802.11g
, Which IEEE wireless standard specify transmission speeds up to 54Mbps? select two -
Answer-802.11a
802.11g
You have been contacted by OsCorp to recommend a wireless solution. - Answer-
802.11g
Which of the following are frequencies defined by 802.11 committees for wireless
networking. select two - Answer-2.4GHz
5.57GHz
Which technologies are used by the 802.11ac standard to increase network bandwidth?
select two - Answer-Eight MIMO radio streams
80MHz donned channels
Your organization uses an 802.11b wireless network. Recently other tenets installed the
following equipment in your building.... - Answer-The wireless tv system
What is the frequency of 802.11a networking? - Answer-5.75GHz
How many total channels are available for 802.11a wireless networks? - Answer-23
How many total channels are available for 802.11g wireless networks? - Answer-11
Which wireless technology is used to enable 802.11a-ht and 802.11g-ht networks to
emulate 802.11n network speeds? - Answer-Channel bonding
You are configuring a wireless network with two wireless access points. Both access
points connect to the same wired network. You want wireless users to be able to
connect to either access point, and to be able to roam between the two access points.
How should you configure the access points? - Answer-Same SSID, different channel.
You have configured a wireless access point to create a small network. You have
configured all necessary parameters. Wireless clients seem to take a long time to find
the wireless access point. You want to reduce the time it takes for the clients to connect.
What should you do? - Answer-Decrease the beacon interval.
You have configured a wireless access point to create a small network. For security,
you have disabled SSID broadcast. From a client computer, you try to browse to find the
access point. You see some other wireless networks in the area, but cannot see your
network to connect to it. What should you do? - Answer-Configure a profile on the
wireless client.
You have a small wireless network that uses multiple access points. The network
currently uses WPA. You want to connect a laptop computer to the wireless network.
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Scholarsstudyguide. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $12.99. You're not tied to anything after your purchase.
