Exam (elaborations)

IICL Container Inspector's Exam Questions and Answers 2024

0 purchase

Course
IICL Container Inspector\'s

Institution
IICL Container Inspector\'s

What does FMCSA stand for? - Answer- Federal Motor Carrier Safety Administration, which operates under U.S. Dept of Transportation (USDOT) FMSCA assumed regulatory authority over chassis operations from what previous administration? - Answer- Federal Highway Administration (FHWA) in 1/1/2000 ...

[Show more]

Preview 4 out of 35 pages

View example

Uploaded on September 28, 2024
Number of pages 35
Written in 2024/2025
Type Exam (elaborations)
Contains Questions & answers

iicl container inspectors
iicl container inspectors exam questions and ans
iicl container inspectors exam questions
iicl container inspectors exam questions 2024
iicl container inspectors exam

Institution IICL Container Inspector's
Course IICL Container Inspector's

Academicaffairs Member since 2 year 246 documents sold

$15.99

Add to cart

Add to wishlist

100% satisfaction guarantee
Immediately available after payment
Both online and in PDF
No strings attached

IICL Container Inspector's Exam Questions and
Answers 2024
Which of the following defects requires repair?
A. A loose door gasket
B. A bent J-bar that does not affect door operation
C. A dent 13mm (1/2 in) deep on the door sill
D. Four dents, each 11mm (7/16 in) deep, on contiguous outboard corrugations of a roof panel -
Answer- A. A loose door gasket

Of the following conditions in a dry-van container, which one would require cleaning?
A. Raised mud foot prints in excess of what might normally remain after a sweep out
B. Dry dust covering dried floor stains as might normally be found after a sweep out
C. Coffee beans remaining inside the container as might occur after a sweep out
D. Polyurethane beads as might be expected to lodge in grooves between floorboards after a
sweep out - Answer- C. Coffee beans remaining inside the container as might occur after a
sweep out

An Equipment Interchange Receipt (EIR), based on an inspection with no damage found, can be
evidence of a container's compliance with: A. Australian Timber Component Treatment
Regulations B. Convention for Safe Containers (CSC) regulations through the ACEP Program
C. Transport under custom's seal (TIR) regulations D. International Standards Organization
(ISO) CEDEX codes regulations - Answer- B. Convention for Safe Containers (CSC) regulations
through the ACEP Program

The top of a replacement plastic ventilator should be centered what distance from the top side
rail? A. 50-55mm (2-2 3/16 in) B. 70-75mm (2 5/8 - 3 in)
C. 100mm (4in) D. 150mm (6 in) - Answer- A. 50-55mm (2-2 3/16 in)

,When must a reference line extend the full length of a bottom side rail? A. When there are two or
more areas of damage on the bottom side rail B. When there is a sharp bend in the bottom side
rail
C. When there is a bowing over the entire bottom side rail D. When there is additional damage to
the bottom side rail so that the reference line cannot be positioned over the ends of the damage -
Answer- C. When there is a bowing over the entire bottom side rail

Which of the following is NOT a transverse structural member of the container?
A. Front sill B. Tunnel rail
C. Rear header
D. Crossmember - Answer- B. Tunnel rail

CORECT ANSWERS 2024
What is traction control? - Answer- Helps the ABS improve vehicle traction by minimizing
wheel slip on the drive axle during acceleration.

What is ABS? - Answer- Antilock braking systems are electronic systems that monitor and
control wheel slip during vehicle braking.

What are the components of ABS? - Answer- electronic control unit (ECU), wheel speed
sensors, modulator valves, exciter rings

In ABS, what is the function of the electronic control unit (ECU)? - Answer- Processes all ABS
info and signal functions. Receives and interprets voltage pulses generated by the sensor pickup
as the exciter teeth pass by, and uses this info to determine: (a) impending wheel lock, and (b)
when/how to activate the ABS modulator valves.

In ABS, what is the function of the modulator valves? - Answer- Regulate air pressure to the
brakes during ABS action. ECU commands mod valve to either change the air pressure to the
brake chamber, or hold the existing pressure.

In ABS, what are the 2 main components of the wheel speed sensors? - Answer- (1) exciter, and
(2) pickup

,In ABS, what is an exciter? - Answer- A ring with notched teeth, also known as sensor ring,
tooth wheel, tone ring, and exciter.

In ABS, what is an pickup? - Answer- Commonly called "the sensor" which contains a wire
coil/magnet assembly, which generates pulses of electricity as teeth of the exciter pass in front of
it.

Which pin/wire is the power supply for ground on a 7-way plug? - Answer- Pin 1 - white

A steel corner fitting is being replaced. To ensure better weld penetration, IICL recommends that
the edges of parts adjacent to the corner fitting be ground to a minimum bevel of? A. 30 degrees
B. 45 degrees
C. 55 degrees D. 60 degrees - Answer- B. 45 degrees

Which of the following components is sometimes placed longitudinally in the container to
support plywood flooring? A. Transverse bow B. Gusset
C. Hat section center spacer
D. Threshold plate - Answer- C. Hat section center spacer

Assuming owner and environmental regulations permit, which of the following procedures is
NOT recommended for repairing tarpaulins or open top containers? A. Cleaning the area to be
covered with acetone or mineral spirit B. Using a heat gun to fuse a patch to the tarpaulin C.
Sewing on a patch of the same material as the tarpaulin D. Repairing a 6 mm (1/4 in ) pin hole
with an epoxy compound - Answer- C. Sewing on a patch of the same material as the tarpaulin

Which of the following is an example of a plank floor condition requiring repair AND which
should be considered as damage?
A. A crack or split with no evidence of impact, which leaks light
B. A crack or split with a sign of impact which does not leak light
C. A crack or split, adjacent to a dented bottom rail, which leaks light

, D. A crack or split, with no evidence of impact, with a loose piece - Answer- C. A crack or split,
adjacent to a dented bottom rail, which leaks light

Welds to corner fittings should be made with?
A. CO2 semi-automatic welding
B. Low hydrogen welding rods
C. Fully automatic welding
D. Arc welding - Answer- B. Low hydrogen welding rods

All of the following procedures are required EXCEPT
A. Weld smoke, spatter, etc. must be removed to permit adhesion of paint
B. The damaged component(s) must be restored as close as possible to original size and profile
C. Welds must be examined using radiographic or magnetic particle non-destructive testing
equipment
D. Replacement steel components must be painted with coating compatible with that originally
applied to the container - Answer- C. Welds must be examined using radiographic or magnetic
particle non-destructive testing equipment

Where should the reference line be placed in order to determine repairworthiness of a
crossmember flange that is bent upwards?
A. Along the inside lower formed edge of the crossmember
B. Spaced out from the crossmember web
C. On the outermost flange surface along the full crossmember length
D. No measurement is necessary - Answer- D. No measurement is necessary

The damaged top rail X below is to be repaired by sectioning. Care must be taken to ensure that
damage area X is NOT cut less than a minimum of
A. 50mm (2 in)
B. 100mm (4 in)
C. 150mm (6 in)

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller Academicaffairs. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $15.99. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

67479 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 15 years now

Start selling

Seller

Exam (elaborations) ·

Exam (elaborations)

IICL Container Inspector's Exam Questions and Answers 2024

Document information

Subjects

Written for