100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
Previously searched by you
Previously searched by you
logo
Electrical Engineering Backflow Assembly Tester Certificate Workshop Multiple Choice Questions and Answers. $16.49
Add to cart
Quickly navigate to
Preview
  2.  
  3. ELECTRICAL ENGINEERING.
  4.  
  5. ELECTRICAL ENGINEERING.

Exam (elaborations)

Electrical Engineering Backflow Assembly Tester Certificate Workshop Multiple Choice Questions and Answers.

 0 purchase
  • Course
  • ELECTRICAL ENGINEERING.
  • Institution
  • ELECTRICAL ENGINEERING.

Electrical Engineering Backflow Assembly Tester Certificate Workshop Multiple Choice Questions and Answers.

Preview 4 out of 37  pages

Document information

  • October 7, 2024
  • 37
  • 2024/2025
  • Exam (elaborations)
  • Unknown

Subjects

  • electrical engineering
  • electrical engineering backflow assembly tester
  • electrical engineering backflow assembly
  • electrical engineering backflow

Written for

  • ELECTRICAL ENGINEERING.
  • ELECTRICAL ENGINEERING.

Seller

avatar-seller
saraciousstuvia

Reviews received

Content preview

Electrical Engineering Backflow Assembly
Tester Certificate Workshop Multiple Choice
Questions and Answers.
1. Backflow is the undesirable reversal of flow of water or other
substances
through a cross
connection into the public water system or consumer's:
a. non potable water system.
b. used water system or consumer's potable water system.
c. public water system or consumer's potable water system.
d. public water system or consumer's non potable system.
Verified Answer -c. public water system or consumer's potable water
system.


2. An approved air gap (AG) is a physical separation between the free-
flowing
end of a:
a. non potable water supply pipeline and the overflow rim of an open or
non-pressurized
receiving vessel.
b. potable water supply pipeline and the overflow drain of an open or
non-pressurized receiving
vessel.
c. potable water supply pipeline and the overflow rim of an open or
pressurized receiving

,vessel.
d. potable water supply pipeline and the overflow rim of an open or
non-pressurized receiving
vessel.
Verified Answer -d. potable water supply pipeline and the overflow rim of
an open or
non-pressurized receiving
vessel.


3. An indirect cross-connection is one that is subject to what type of
backflow?
a. only back siphonage
b. only backpressure
c. only low hazard, back siphonage or backpressure
d. high or low hazard, back siphonage or backpressure
Verified Answer -a. only back siphonage


4. Cross-connections between the potable water piping and any piping or
containers
containing substances not approved as potable water must be either
eliminated or
controlled by the installation of an:
a. air gap or a backflow prevention device.
b. approved air break or an backflow prevention device.
c. approved air gap or an approved backflow prevention device.

,d. approved air gap or an approved backflow prevention assembly.
Verified Answer -d. approved air gap or an approved backflow prevention
assembly.


5. While testing CV#2 of a DCVA, if CV #2 leaks, the BAT would observe
that the
water flow:
a. stops from the sight tube at TC #3 and no differential shows on the
gauge.
b. stops from the sight tube at TC #4 and at least 1.0 psid shows on the
gauge.
c. continues from the sight tube at TC #4 and at least 1.0 psid shows on
gauge
d. stops from the sight tube at TC #4 and no differential shows on the
gauge.
Verified Answer -d. stops from the sight tube at TC #4 and no differential
shows on the gauge.


6. Service protection is a way to protect a public water system from
contamination due to backflow from the customer's water system by the
installing an approved
backflow preventer at the:
a. service connection which is considered to be at or near the water meter.
b. service connection which is considered to be the end of the customer's
potable water system furthest from the meter
c. point of use which is considered to be the start of the customer's potable
water system where the pipe goes through the outside wall of the
building.

, d. point of use which is normally considered to be inside the building.
Verified Answer -a. service connection which is considered to be at or near
the water meter.


7. A Washington state certified Backflow Assembly Tester is certified to:
a. inspect, test and repair backflow prevention assemblies.
b. inspect, test and monitor backflow prevention devices.
c. inspect, test and repair backflow prevention devices.
d. inspect, test and monitor backflow prevention assemblies.
Verified Answer -d. inspect, test and monitor backflow prevention
assemblies.


8. The RPBA is designed so that if a check valve leaks, the relief valve
may:
a. close to prevent water from entering the relief valve vent.
b. open to discharge through the relief valve vent.
c. open to discharge through the zone of reduced pressure.
d. close to prevent water from entering the zone of reduced pressure.
Verified Answer -b. open to discharge through the relief valve vent.


9. An AG installed in lieu of an approved backflow prevention assembly
must
be inspected for
compliance with the definition of an approved air gap by:
a. only a BAT.
b. only a CCS.
c. either a CCS or a BAT.

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller saraciousstuvia. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $16.49. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

69252 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 15 years now

Start selling
$16.49
  • (0)
Add to cart
Added