Aquastat Study guides, Class notes & Summaries

4th Class Power Engineering Unit A9 Chapter 6: Electrical Control Systems 100% Verified This type of thermostat is equipped with an open-contact switch or a snap switch: Select one: a. on-off control b. two position c. modulating d. multipositon a A two-terminal variable resistor used for varying current in a circuit is known as a: Select one: a. potentiometer b. rheostat c. thermistor d. photoresistor b These can be either normally closed or normally open: Select one...

MN Boiler license 2023 Exam Questions with Complete Solutions What is the unit called that controls starting and stopping of the burner by sensing temperature of water in a hot water boiler? - Answer-Aquastat What controls the temperature of the water in a hot water boiler system? - Answer- Aquastat or remote temperature monitoring system What safety devices should be installed on a hot water heating boiler? - Answer-Code safety valve(s) Low water fuel cutoff What removes air from a h...

MN Boiler license Exam Questions and Answers Graded A+ What is the unit called that controls starting and stopping of the burner by sensing temperature of water in a hot water boiler? - Aquastat What controls the temperature of the water in a hot water boiler system? - Aquastat or remote temperature monitoring system What safety devices should be installed on a hot water heating boiler? - Code safety valve(s) Low water fuel cutoff What removes air from a hot water boiler system? - A...

MN Boiler license 2023 Exam Questions with Complete Solutions What is the unit called that controls starting and stopping of the burner by sensing temperature of water in a hot water boiler? - Answer-Aquastat What controls the temperature of the water in a hot water boiler system? - Answer-Aquastat or remote temperature monitoring system What safety devices should be installed on a hot water heating boiler? - Answer-Code safety valve(s) Low water fuel cutoff What removes air from a...

MN Boiler License Q&A Latest 2024 What is the unit called that controls starting and stopping of the burner by sensing temperature of water in a hot water boiler? - Answer -Aquastat What controls the temperature of the water in a hot water boiler system? - Answer -Aquastat or remote temperature monitoring system What safety devices should be installed on a hot water heating boiler? - Answer -Code safety valve(s) Low water fuel cutoff What removes air from a hot water boiler system? - Answ...

Gas Fitter 2 Practice Test - Questions and Answers Installation of one 400,000 btu natural draft boiler in a tight enclosure would require an air supply opening of? A. 114 sq in B. 50 sq in C. 58 sq in D 112 sq in With the installation of a 75,000 btu atmospheric hot water tank in a tight house, how much free air is required when using a round duct? A. 11" B. 4" C. 7" D. 3" A portable infrared heater that cannot be interlocked shall be connected to a: A. CO2 monitor alarm B. CO monitor ala...

MN Special Boiler License Exam Guide for MHS Custodians Questions With Verified Answers High Pressure Boiler - answerAbove 15psi steam & 160psi water pressure After blowing down column and glass the water should return how? - answerQuickly When entering a steam boiler room what is the first thing an operator should do? - answerCheck water level What type of safety valve is required - answerA.S.M.E. approved direct spring loaded When operating a boiler what is most important? - answerSafe...

Gas tech II Exam Questions And Answers 1) What is the minimum diameter of a pressure gauge needed to perform a leak test on gas piping? - ANS 3" 2) Amp meter can read what? - ANS Conductor magnetic field. 3) What would be the primary voltage of a furnace? - ANS 120/1/60. 4) What is the function of an intermittent pilot? - ANS Stay on during the main burner operation. 5) What is the millivolts power output on a thermocouple closed circuit test? - ANS 10 to 15 ...

Massachusetts Oil burner Practice Questions with Complete Solutions The cross connection between two supply tanks shall not exceed? 660 gallons When is an automatic draft control not required? When the equipment is designed to control the draft. Combustion performance testing can indicate: Improper air oil mixture, too much combustion air, and low pump pressure. If a second oil-burning appliance is installed in a single chimney, you must insure: Sufficient draft is available for ...

Stationary Engineer License Exam Prep - Complete Solutions (Answered) The pressure sensitive device attached to a fan housing is called a a. pressuretrol b. aquastat c. thermostat d. vaporstat Draft is measured in a) ounces per square inch b) inches of water c) inches of mercury d) pounds per square inch Which of the following is used to measure temperature? a. fyrite analyzer b. vaporstat c. orsat analyzer d. pyrometer The main stop valve is located on the a) oil supply line b) condensate bre...