Ase brake exam 2025 - Study guides, Class notes & Summaries

ASE C1 EXAM PRACTICE QUESTIONS AND ANSWERS A customer is concerned about brake noise on their vehicle. The service consultant should: A. Explain that brake noise is common on all vehicles. B. Ask the customer to imitate the noise C. Explain that a technician will need to evaluate the vehicle. D. Give the customer an average price for a brake job - Ans:-C A customer comes in for a 30,000 mile service. While completing the service, the technician notes that the vehicle will soon need the f...

ASE S4 Brakes Exam Practice Questions and Answers The air system is maintained at what pressure? - Answer️️ -100 to 120 pounds per square inch. At what pressure does the low pressure switch activate? - Answer️️ -Below 60 pounds per square inch. A safety or pop off valve is usually installed in which reservoir? - Answer️️ -In the one closest to the compressor. Why is the Wet tank referred to as such? - Answer️️ -It is the one closest to the compressor and has the most wate...

ASE (Entry level technician prep) - Brakes A5 Exam Practice Questions and Answers (100% Pass) A5 Question 1 The brake pedal is low and spongy; all brake adjustments have been completed according to specifications. The cause of the problem could be: A) Binding pedal linkage. B)Dented brake line. C)Plugged compensating port. D)A weak hydraulic hose. - Answer️️ -Answer D is correct! Binding pedal linkage would cause a hard pedal and perhaps an effective brake system. This is also tru...

ASE BRAKES Exam #1 Practice Questions and Answers A drum is chattering on the brake lathe. This could be the result of: A. Failure to install the dampening belt. B. Cutting too slowly. C. Dull cutting blades. D. Cutting speed too fast. - Answer️️ -A A vehicle is equipped with a hydro-boost brake system has a hard pedal with little braking action. Which of the following could be the cause? A. Low brake fluid B. Air in the brake fluid C. Low power steering fluid D. An overtightene...

ASE BRAKES Exam #4 Practice Questions and Answers (100% Correct) Four channel ABS sensors will have how many ABS wheel speed sensors? A. Two B. Four C. Six D. Eight - Answer️️ -B The metering valve: A. Limits front brake application until the rear brakes apply. B. Limits rear brake application until the front brakes apply. C. Limits front brake application based on vehicle height. D. Limits rear brake application based on vehicle height. - Answer️️ -A A wheel cylinder has b...

ASE B-5 Mechanical/Electrical Practice Exam Questions and Answers A vehicle is brought in with a bent subframe. Technician A says to section the subframe. Technician B says the subframe should not be repaired and must be replaced. Who is right? A, B, Both, or Neither - Answer️️ -Technician B only The subframe should never be sectioned, and should rarely, if ever, be worked. It is typically a bolt-on part that does not lend itself to traditional straightening methods. Vehicle manufact...

ASE A5 Brakes Exam Questions And Solutions(Well Elaborated)2024/2025 A spongy brake pedal may be caused by: a. ABS Diagnostic Trouble Code set b. Frozen caliper piston c. Defective metering valve. d. Air in hydraulic system - answers D. This question has the word EXCEPT. For this question, look for the choice that could NOT cause the described situation. Read the entire question carefully before choosing your answer. A vehicle has a very erratic brake pulling concern while applying t...

ase exam practice questions and answers A technician is performing a load test on a battery and finds the battery to below specifications. Which of the following is the best action to taken next? a Perform a resistance test on the battery b Recharge the battery and sell it as a used battery c Recharge the battery and retest it d Drain the battery completely and recharge it - Answer️️ -c Recharge the battery and retest it Two technicians are discussing a whining noise heard through th...

ASE BRAKES Exam #1 Practice Questions and Answers A - Answer-A drum is chattering on the brake lathe. This could be the result of: A. Failure to install the dampening belt. B. Cutting too slowly. C. Dull cutting blades. D. Cutting speed too fast. C - Answer-A vehicle is equipped with a hydro-boost brake system has a hard pedal with little braking action. Which of the following could be the cause? A. Low brake fluid B. Air in the brake fluid C. Low power steering fluid D. An overtight...

ASE Certification Exam Questions and answers Both b and c - Answer-Coolant should be tested for ________. Proper color Freezing point (temperature) Specific Gravity Both b and c Both technician a and b - Answer-Two technicians are discussing a compression test. Technician A says that the engine should be cranked over with the pressure gauge installed for "4 puffs." Technician B says that the maximum difference between the highest reading cylinder and the lowest reading cylinder s...