In a drum brake assembly Study guides, Class notes & Summaries

on a car with disc/drum brakes, the front brakes grab quickly when light pedal pressure is applied. This problem could be caused by a bad.. - correct answer metering valve the drive of a vehicle with power disc/drum brakes says that the brake pedal moves slowly to the floor while maintaining pedal pressure at a spotlight. what could cause this problem? - correct answer leaking primary piston cup in master cylinder which of the following would most likely happen if the measurements taken f...

ASE BRAKES Exam #3 Questions and Answers (Graded A) The goal of burnishing the brakes after a complete brake service is to: A. Heat the brake assembly. B. Cool the brake assembly. C. Set the wheel bearings. D. Stretch the brake shoes to match the drum. - CORRECT ️️ A Which of the following is true concerning master cylinder pushrod adjustment? A. There should be a slight gap between the pushrod and master cylinder piston. B. It should be adjusted until the piston is pushed in slightl...

C - ANSWER-What would a C-clamp be used for during disc brake service? A. Seating the pads on the rotor B. Seating the caliper on the guides C. Retracting the piston in the bore D. Compressing the pads into the piston D - ANSWER-The red brake warning light illuminates when the brake pedal is depressed. Which of the following is the LEAST LIKELY cause? A. Air in the front brake system B. Air in the rear brake system C. Low brake fluid level D. Faulty ABS pump assembly B - ANSWER-Whi...

In a single anchor bendix drum type rear brake - correct answer the secondary lining is longer than the primary Compared to the secondary shoe lining areas of drum brakes, the primary shoe lining area is: - correct answer smaller and goes toward the front of the car During a brake overhaul, you notice that the brake fluid seems to be very dirty and dark in color. What should you do? - correct answer flush the system before the new parts are installed In order to bleed the system on a vehi...

ASE A5 Test Questions with 100% Correct Answers | Latest Version 2024 | Verified 1. On a car with disc/drum brakes, the front brakes grab quickly when light pedal pressure is applied. This problem could be caused by a bad: A. proportioning valve B. pressure safety switch C. metering valve D. residual check valve - C 2. The driver of a vehicle with power disc/drum brakes says that the brake pedal moves slowly to the floor while maintaining pedal pressure at a stoplight. What could c...

Crane Course Questions and Answers Graded A+ According to OSHA, when traveling a crane at a jobsite with no load under or near power lines, a spotter is required if any part of the crane will get closer than? 20 feet Within what percentage of level does a telescopic boom crane have to be for the gross ratings in the load chart to remain valid? 1% Brainpower Read More Previous Play Next Rewind 10 seconds Move forward 10 seconds Unmute 0:04 / 0:15 Full screen which o...

In a single anchor bendix drum type rear brake - the secondary lining is longer than the primary Compared to the secondary shoe lining areas of drum brakes, the primary shoe lining area is: - smaller and goes toward the front of the car During a brake overhaul, you notice that the brake fluid seems to be very dirty and dark in color. What should you do? - flush the system before the new parts are installed In order to bleed the system on a vehicle equipped with power brakes: - None of t...

Disc brakes use replaceable friction material called __________. - Correct Answer Pads Drum brakes use replaceable friction material called ________. - Correct Answer Shoes Technician A says that a power-assisted brake reduces stopping distances compared with a non-power-assisted brake system. Technician B says that the power-assisted brake system reduces the force that the driver must exert on the brake pedal. Which technician is correct? - Correct Answer Technician B only A locked whe...

HEAVY TRUCK BRAKES MICHIGAN MECHANIC STUDY GUIDE Graded A+ AN ENGINE BRAKE (JACOBS BRAKE) A. IS A SELF-ENERGIZING SERVO TYPE. B. IS NORMALLY USED IN PLACE OF A SPRING BRAKE. C. RESTRICTS THE INTAKE PORT AND CAUSES A BUILD UP OF 30-45 LBS OF PRESSURE. D. OPENS THE EXHAUST VALVES NEAR THE TOP OF THE COMPRESSION STROKE TO RELEASE THE COMPRESSED AIR. (CORRECT AWNSER) IN THE SYSTEM SHOWN BELOW, THE PART AT C IS: A. AN INVERSION VALVE. (POSSIBLE CORRECT AWNSER) B. A SAFETY VALVE. C. A MOD...

HEAVY TRUCK BRAKES MICHIGAN MECHANIC STUDY GUIDE AN ENGINE BRAKE (JACOBS BRAKE) A. IS A SELF-ENERGIZING SERVO TYPE. B. IS NORMALLY USED IN PLACE OF A SPRING BRAKE. C. RESTRICTS THE INTAKE PORT AND CAUSES A BUILD UP OF 30-45 LBS OF PRESSURE. D. OPENS THE EXHAUST VALVES NEAR THE TOP OF THE COMPRESSION STROKE TO RELEASE THE COMPRESSED AIR. (CORRECT AWNSER) IN THE SYSTEM SHOWN BELOW, THE PART AT C IS: A. AN INVERSION VALVE. (POSSIBLE CORRECT AWNSER) B. A SAFETY VALVE. C. A MODULATOR VAL...