Pin diagram - Study guides, Class notes & Summaries

NATE CORE EXAM QUESTIONS WITH A GRADED SOLUTIONS Pictorial wiring diagrams typically show components__ - Answer-In their approximate positions in the equipment A ladder diagram is useful for? - Answer-Troubleshooting a unit An analog VOM meter is an electrical meter that__ - Answer-Displays volts, ohms, or milliamperes on an analog scale A digital multi meter marked "auto-ranging" Will automatically set itself for__ - Answer-Reading take and range of values for all volts, amps o...

Where is the best location for leveling a crane? - upper works When determining the "gross load" the best method is: - get an accurate load weight and add the rigging By order of hitch strength, which is the correct answer? - basket, vertical, choker What is the purpose of using a jib? - increase height When taking a side strain on a boom, what concerns the operator most? - boom damage OSHA requires you to always have at least how many wraps on a hoist drum? - 2 On a load chart, values a...

The scale on the drawing is 1/8"=1. What is the actual length of a line that measures 2" 1/4' on the drawing? Correct Answer 6 ft? 18 ft? Which of the following measure the specific gravity of the electrolyte of a wet cell battery? Correct Answer Hydrometer A possible cause for an air conditioner compressor to run continuously is a Correct Answer Defective low pressure control switch? Shortage of refrigerant? Threads are cut in a rod by rotating the die stick 1/4 turn back for each 1...

A nurse is contributing to the plan of care for a client who is at risk for osteoporosis. Which of the following interventions should the nurse include to prevent bone loss? Encourage weight-bearing exercises. r-Weight-bearing exercises, such as walking, can maintain bone mass by reducing bone demineralization, thus helping to prevent osteoporosis. A nurse is reinforcing discharge instructions with a client who is postoperative following a right hip arthroplasty. Which of the followin...

When working on rubber, cranes are rated at what percentage of tipping: a) 70% b) 75% c) 80% d) 85% - 75% When a crane is working "on outriggers" the only time they should be less than fully extended is when: a) working alongside the highway and cannot block a lane b) you are handling light loads c) the main boom is being lifted d) there is a load chart for this operation - there is a load chart for this operation A truck crane set up with the outriggers extended and set, and tires t...

When working on rubber, cranes are rated at what percentage of tipping: a) 70% b) 75% c) 80% d) 85% Correct Answer: 75% When a crane is working "on outriggers" the only time they should be less than fully extended is when: a) working alongside the highway and cannot block a lane b) you are handling light loads c) the main boom is being lifted d) there is a load chart for this operation Correct Answer: there is a load chart for this operation A truck crane set up with the outrigge...

Associate CET Practice Exam - Questions and Answers A schematic used in electronic servicing: is much like a road map for following signals High voltage should be discharged before servicing a product. After disabling. After disabling AC input power, discharge an HV PS by: draining through a large value resistor to chassis ground Which of these would be an important electrical consideration in the use of a transformer? The operating frequency If a 12v product is dissipating 50w, how much load ...

Structure tructure Analysis nalysis Structure Design Against Static Load 1. Introduction to Structure .................................................................................................... 3.1 – 3.2 2. Determinacy and Indeterminacy ......................................................................................... . 3.3 – 3.12 3. Influence Line Diagram .......................................................................................................

NCCCO CORE FINAL EXAM QUESTIONS AND ANSWERS LATEST UPDATE 2024/2025 (100% CORRECT) Before leveling a mobile crane on outriggers, an operator should ensure: - ANSWER there is no weight of the crane bearing on any tires Operating a mobile crane with a long boom, on uneven ground, what support condition should be considered? - ANSWER Keeping 90 degree angle between cylinder rod and pad What is the primary purpose fir a rooster sheave or auxiliary boom point sheave? - ANSWER Separate the boom h...

Rotation-resistant rope may be used with a swivel - If the rope manufactory approves Working radius is defined as the distance from the - Center of rotation of the crane to the center of gravity of the load At what percentage of tipping are truck-mounted cranes on outriggers, which are fully extended and set, rated - 85% What is the primary purpose of the (LMI) load moment indicator - It will warn operator of overload conditions Wire rope clips used in conjunction with wedge sockets must be ...