Sspc pa 2 - Study guides, Class notes & Summaries

NACE CIP 1 CBT EXAM PRACTICE QUESTIONS With 100% Correct Answers Dew point is the temperature at which - answercondensation occurs. You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining. Your FIRST preferred course of action is to: - answerDocument the problem and advise the Contractor and Owner's representative. If a contractor is using a po...

NACE CIP I CBT Final EXAM PRACTICE QUESTIONS AND ANSWERS Latest Graded A+ 2023 | 2024. What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial type magnetic pull off Dry Film Thickness(DFT) gauge? - answer2.5 cm (1 inch) Polymerization is the process of? - answerMonomers joining together. An exposed area of the substrate or previous coat of a conductive material, often caused by poor application technique is called: - answerHoliday ...

When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that: - Answer-Synthetic oil or grease may not be identified To achieve consistently accurate results with ALL alt test equipment - Answer-wash your hands before sampling. When holiday testing is required the Inspector is always required to enforce NACE SP 0188: - AnswerTrue If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction leve...

NACE SP0188 - Answer-High and Low Voltage Holiday Testing Low-Voltage Holiday Detector - Answer--Ground is attached directly to substrate. -Sponge saturated with a solution of tap water/wetting agent -Proper mix ratio 1oz/USgal -Proper of speed is 1ft/sec Double Stroke -Used on Coatings up to 20mils -may be used on concrete Low Voltage Holiday Detectors Common Errors - Answer--Failure to Keep probe in contact with surface -Moving the electrode too fast or slow -Over or under saturating ...

Coating Inspector Level 1 Exam Questions With 100% Correct Answers When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that: - answerSynthetic oil or grease may not be identified To achieve consistently accurate results with ALL alt test equipment - answerwash your hands before sampling. When holiday testing is required the Inspector is always required to enforce NACE SP 0188: - answerTrue If the specifier does not identify a restricti...

NACE CIP1 Exam Sample Questions with Verified Answers| Latest 2023/ 2024 1. You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if ...

NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS GRADED A+ Dew point is the temperature at which condensation occurs. You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining. Your FIRST preferred course of action is to: Document the problem and advise the Contractor and Owner's representative. If a contractor is using a poorly maintained comp...

Dew point is the temperature at which - condensation occurs. You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining. Your FIRST preferred course of action is to: - Document the problem and advise the Contractor and Owner's representative. If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conve...

When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that: - Synthetic oil or grease may not be identified To achieve consistently accurate results with ALL alt test equipment - wash your hands before sampling. When holiday testing is required the Inspector is always required to enforce NACE SP 0188: - True If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is: - Level 3 Fin...

NACE CIP1: Standards Questions and Answers 100% Verified NACE No. 1/SSPC-SP 5 White Metal Blast Cleaning; free from all visible mill scale, rust, and coatings with 0% staining NACE No. 2/SSPC-SP 10 Near White Metal Blast Cleaning; free from all visible mill scale, rust, coatings with 5% staining allowed NACE No. 3/SSPC-SP 6 Commercial Blast Cleaning; free from all visible mill scale, rust, coatings with 33% staining allowed NACE No. 8/SSPC-SP 14 Industrial Blast Cleaning; allows tightly adher...