Camber - Study guides, Class notes & Summaries

ASE G1 (GENERAL AUTOMOBILE MAINTENANCE) EXAM 2024 Toe can cause tire wear if not within manufacturer's specifications (True or False) - ANSWER ☑☑True Camber can cause tire wear if not within manufacturer's specifications (True or False) - ANSWER ☑☑True Caster can cause tire wear if not within manufacturer's specifications (True or False) - ANSWER ☑☑False Technician A says that a PAX run-flat tire uses a special wheel. Technician B says that a standard tire ca...

HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? - Correct Answer ️️ -A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHI...

YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? - A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHINGS WOULD BE FOUND AT: - A. POINT B. B. POINT C. C. POINT A. (CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWN...

A vehicle is brought in with a bent subframe. Technician A says to section the subframe. Technician B says the subframe should not be repaired and must be replaced. Who is right? A, B, Both, or Neither - Answer- Technician B only The subframe should never be sectioned, and should rarely, if ever, be worked. It is typically a bolt-on part that does not lend itself to traditional straightening methods. Vehicle manufacturers recommend replacement. The first step in bleeding brakes is to: ...

HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? - Correct Answer ️️ -A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHI...

HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? - Correct Answer ️️ -A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHI...

The above alignment setting would results in which of following conditions - Answer-Right tire wear on the inside, vehicle pulls to the left Reason: the vehcile will always pill to the side with (+) camber A driver says that the front end of his car vibrates up-and-down while traveling at most road speeds . Technician A says that too much runout of the front wheels could be the cause. Technician B says that static out-of-balance of the front wheels could be the cause. Who is right ? - Answ...

HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC >> HEAVY TRUCK ELECTRICAL MICHIGAN MECHANIC Combined Sets Exam Questions With Revised Correct Detailed Answers |ALREADY GRADED A+ PASS 2024 >> BRAND NEW VERSION! 1) WHAT IS THE FIRST THING TO CHECK IN A CASE OF HARD STEERING? - A. AIR PRESSURE IN TIRES. (CORRECT AWNSER) B. CAMBER SETTINGS. (NOT CORRECT AWNSER) C. DRAG LINK SETTINGS. D. STEERING COLUMN LUBRICATION. (NOT CORRECT AWNSER) 2) YOU HAVE DETERM...

Bleeding a power steering unit is generally done by turning the steering wheel left and right repeatedly After rounding a turn, the front wheels do not return to the straight ahead position in a normal way. What adjustment is most likely to be out of specifications? Caster "Toe" adjustment on front wheel drive vehicles is made by: changing he length of the steering linkage When performing a front-end alignment what should you do before you adjust the toe setting? adjus...

NIFE AERO QUESTIONS AND ANSWERS RATED A+ What is a vector? direction and magnitude What is air density? Total mass of air particles per unit volume. m/v What is a moment? Force that is moved some distance. What are the requirements for an airplane to be in equilibrium flight? Sum of all forces and all moments around the center of gravity are equal to 0 Can equilibrium flight be achieved in a turn? No. Acceleration is occurring. There are moments What are the requirements for an a...