ABYC Marine Revision Bundle contains challenging Questions in Marine Systems and Operations. it also ventures into additional knowledge essential for Marine students. It's the Best for Exam revision.
[Show more]
1. minimum spacing between hull vent openings and fuel fill or vent fittings should be - 15 inches 2. thermal efficiency of a diesel engine is such that typical heat converted to useful power is approximately what percent of total heat - 36% 3. What is the primary difference between the gasoli...
Preview 2 out of 9 pages
Add to cart1. minimum spacing between hull vent openings and fuel fill or vent fittings should be - 15 inches 2. thermal efficiency of a diesel engine is such that typical heat converted to useful power is approximately what percent of total heat - 36% 3. What is the primary difference between the gasoli...
B. 15 inches Based on ABYC standards, minimum spacing between hull vent openings and fuel fill or vent fittings should be: A. 9 inches B. 15 inches C. 24 inches D. 36 inches D. 36% The thermal efficiency of a diesel engine is such that typical heat converted to useful power is approximate...
Preview 4 out of 31 pages
Add to cartB. 15 inches Based on ABYC standards, minimum spacing between hull vent openings and fuel fill or vent fittings should be: A. 9 inches B. 15 inches C. 24 inches D. 36 inches D. 36% The thermal efficiency of a diesel engine is such that typical heat converted to useful power is approximate...
Black soot around the engine compartment openings might indicate: - Insufficient engine room ventilation if the engine does not achieve full rpm, what test would be the last to be performed? - compression check The exhaust blower switch is activated but the sound coming from the blower is no...
Preview 2 out of 7 pages
Add to cartBlack soot around the engine compartment openings might indicate: - Insufficient engine room ventilation if the engine does not achieve full rpm, what test would be the last to be performed? - compression check The exhaust blower switch is activated but the sound coming from the blower is no...
The minimum amp circuit breaker that should be used to protect a 120V water heater circuit with a 1600-watt element would be rated at ___________ amps. A. 15 When testing for excessive EMF emission near a conductor or appliance, the tool of choice is a (n): C. Gauss meter What is the symbol fo...
Preview 4 out of 35 pages
Add to cartThe minimum amp circuit breaker that should be used to protect a 120V water heater circuit with a 1600-watt element would be rated at ___________ amps. A. 15 When testing for excessive EMF emission near a conductor or appliance, the tool of choice is a (n): C. Gauss meter What is the symbol fo...
2x sold
Polyethylene What is the most often used material for potable water system tanks? 1. Copper Alloys (incl. bronze, brass and nickel-copper) 2. AISI Type 300 series stainless steel 3. Glass-lined metal 4. FDA approved plastic 5. FDA approved rubber Name 5 materials allowable for contact use in ...
Preview 4 out of 52 pages
Add to cartPolyethylene What is the most often used material for potable water system tanks? 1. Copper Alloys (incl. bronze, brass and nickel-copper) 2. AISI Type 300 series stainless steel 3. Glass-lined metal 4. FDA approved plastic 5. FDA approved rubber Name 5 materials allowable for contact use in ...
What is the most often used materials for potable water systems? - Polyethylene Name 5 materials allowable for contact use in potable water systems: - 1. Copper Alloys (incl. bronze, brass and nickel-copper) 2. AISI Type 300 series stainless steel 3. Glass-lined metal 4. FDA approved plastic ...
Preview 4 out of 34 pages
Add to cartWhat is the most often used materials for potable water systems? - Polyethylene Name 5 materials allowable for contact use in potable water systems: - 1. Copper Alloys (incl. bronze, brass and nickel-copper) 2. AISI Type 300 series stainless steel 3. Glass-lined metal 4. FDA approved plastic ...
E - Ball valves may be sealed to through hull fittings with: A. 5200 B. SikaFlex C. Teflon D. All the above E. None of the above B - Tubes are measured by: A. ID B. OD C. nominal size C - pipes may not be connected by: A. Welding B. Threaded fittings C. Compression fittings D...
Preview 4 out of 39 pages
Add to cartE - Ball valves may be sealed to through hull fittings with: A. 5200 B. SikaFlex C. Teflon D. All the above E. None of the above B - Tubes are measured by: A. ID B. OD C. nominal size C - pipes may not be connected by: A. Welding B. Threaded fittings C. Compression fittings D...
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Stuvia is a marketplace, so you are not buying this document from us, but from seller masigabethwel. Stuvia facilitates payment to the seller.
No, you only buy these notes for CA$22.17. You're not tied to anything after your purchase.
4.6 stars on Google & Trustpilot (+1000 reviews)
79271 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now