Exam (elaborations)
Texas Wastewater Class A Exam Questions With Answers 100% Correct
- Course
- Institution
Texas Wastewater Class A Exam Questions With Answers 100% Correct
[Show more]
3 reviews
By: big4john2005 • 5 months ago
Helpful
By: fluxxcd • 7 months ago
Too many repeat questions..no questions on lagoons and acre feet..I just took test..
By: jigalater • 11 months ago
Seller
Follow
Boffin
Reviews received
Content preview
Texas Wastewater Class A Exam Questionsand Answers 100% Correct
What is TCEQ doing to control "point source" pollution of the Texas waterways?
-Permitting of domestic wastewater plants
-Permitting of industrial wastewater plants
Describe proper design of force main wastewater lines. - Minimum two fps velocity
with the smallest pump operating alone. Minimum four inch diameter pipe with 150
psi rating.
What is Standard Dimension Ratio? - Ratio of outside pipe diameter (OD) to wall
thickness (PVC)
Describe proper design of gravity wastewater lines. - Designed to flow half full
,under normal conditions, at a minimum of two fps and a maximum of ten fps.
Manholes should have a minimum opening of? - 24 inches and be at least 4 feet wide.
pH meters should be calibrated how often? What standards should be used for
calibration purposes? - Daily with at least two buffers.
What is the standard chlorine residual and minimum contact time on Texas
wastewater permits? - a. 1.0 mg/L for a minimum 20 minutes detention time at peak
flow b. No chlorine residual needed if detention time is greater than 21 days
As the complexity of an organization increases, what management function becomes
most important? - Planning
What is the effective chlorine disinfecting agent? - Hypochlorous Acid (HOCl)
Does pH affect the chlorination process? Explain your answer. - When using free
chlorine the disinfectant is HOCl acid. As such it is much more effective at pH's below
7.0. Above 7.0 pH the acid begins to be neutralized.
What is the effluent chlorine residual in Texas that is standard on permits and the
minimum detention time? What is the maximum residual allowed? - Texas standard
is 1.0 mg/L for a minimum 20 minutes detention time at peak flow. Maximum
residual allowed is 4.0 mg/L.
A treatment plant has a clarifier that is 60 feet in diameter and is 10 feet deep. The
weir is 2 feet inside the outer clarifier wall. The flow is 1.0 MGD. The weir and
outflow channel is 3 feet deep. a. What is the detention time in hours? - Formula
, What activated process cannot nitrify in a single stage? - Contact Stabilization
What is the GPM output of a piston pump with an 8-inch diameter piston with a 10-
inch stroke operating at 50 strokes per minute? - Formula
A treatment plant has a clarifier that is 60 feet in diameter and is 10 feet deep. The
weir is 2 feet inside the outer clarifier wall. The flow is 1.0 MGD. The weir and
outflow channel is 3 feet deep.
a. What is the detention time in hours?
b. What is the surface loading in gal/ft2/day?
c. What is the weir loading in gal/linear ft/day? - Formulas
A primary clarifier has a flow of 3.0 MGD and has a diameter of 100 feet. It is 12 feet
deep and has 24 inches of freeboard. What is the detention time in hours? - Formulas
Anaerobic digester gas should contain? - 65-75% methane, 25-35% carbon dioxide
and 1-5% nitrogen.
An activated sludge plant has an average daily flow of 3.5 MG. The aeration tank
capacity is 1.2 MG with a MLSS concentration of 3200 mg/L. The clarifier has a
capacity of 400,000 gallons with a MLSS concentration of 6,000 mg/L. The wasting
rate is 40,000 gallons per day with a MLSS concentration of 8, 000 mg/L. The effluent
TSS is 18 mg/L. Assuming volatile concentrations of 70%, what is the MCRT and what
type of activated sludge plant should this be? - Formulas MCRT
What are some of the causes of filaments in the aeration basin? - a. low DO
b. low organic loading
c. septic wastes
d. nutrient deficiencies .
e. high sulfur content
Good sludge quality will have a predominance of what organisms in the MLSS? -
Ciliated protozoa
When an RBC is operating correctly, how will the slime appear on the media? - Grey
to brown 0.05 to 0.1 inches thick
According to design criteria, what are the minimum allowable diameters for a
manhole? - 24 inch opening and 48 inch inside diameter
What activated sludge process does not achieve complete nitrification? - Contact
Stabilization
In the selection of forced main wastewater piping, what is the minimum working
pressure? - 150 psi
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Boffin. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for CA$25.89. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
67096 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now
Recently viewed by you
