100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
TestOut Networking Pro Ch 4 Exam Questions and Answers CA$14.67   Add to cart

Exam (elaborations)

TestOut Networking Pro Ch 4 Exam Questions and Answers

 14 views  0 purchase
  • Course
  • Institution

TestOut Networking Pro Ch 4 Exam

Preview 2 out of 6  pages

  • February 2, 2024
  • 6
  • 2023/2024
  • Exam (elaborations)
  • Questions & answers
avatar-seller
TestOut Networking Pro Ch 4 Exam
Topology - Answer- Ethernet uses the following networking topologies, depending upon
the specification being implemented:
• Physical bus, logical bus
• Physical star, logical bus
• Physical star, logical star

Networking Device - Answer- Devices used on Ethernet networks include:
• NICs
• Hubs (obsolete)
• Switches
• Routers

Transmission Media - Answer- Ethernet supports the following cable types:
• Unshielded twisted pair (UTP) cables with RJ45 connectors. This is the most common
transmission medium used for Ethernet.
• Fiber optic cables, most commonly used in high-speed applications, such as servers
or streaming media.
• Coaxial cables for older Ethernet implementations (often called thinnet or thicknet
networks).

Media Access Method - Answer- Ethernet uses a contention-based media access
method defined by the IEEE 802.3 standards called Carrier Sense, Multiple
Access/Collision Detection (CSMA/CD). Devices use the following process to send
data:
• Because all devices have equal access (multiple access) to the transmission media, a
device listens to the transmission medium to determine if it is free before sending data
(carrier sense).
• If it is not free, the device waits a random amount of time and listens again to the
transmission medium. If it is free, the device transmits its message.
• If two devices transmit at the same time, a collision occurs. The sending devices
detect the collision (collision detection) and send a jam signal to notify all other hosts
that a collision has occurred.
• Both devices wait a random length of time before attempting to resend the original
message (backoff).
Devices with collision detection turned on operate in half-duplex mode; devices with
collision detection turned off operate in full-duplex mode

Half Duplex - Answer- • Collision detection is turned on.

, • The device can send or receive in only one direction at a time.
• Devices connected to a hub must use half-duplex communication.
Up to the rated bandwidth (10 Mbps for 10BaseT, 100 Mbps for 100BaseT, etc.)

Full Duplex - Answer- • Collision detection is turned off.
• The device can send and receive at the same time.
• Requires full-duplex capable NICs.
• Requires switches with dedicated switch ports (a single device per port).
Double the rated bandwidth (20 Mbps for 10BaseT, 200 Mbps for 100BaseT, etc.)

Physical Addresses - Answer- Ethernet devices are identified by using the MAC
address, which is burned into the network interface card.

Frames - Answer- is a unit of data that is ready to be sent on the network medium.
Ethernet frames contain the following components:
• The preamble is a set of alternating ones and zeros terminated by two ones (11) that
mark it as a frame.
• The destination address identifies the receiving host's MAC address.
• The source address identifies the sending host's MAC address.
• The data is the information that needs to be transmitted from one host to the other.
• Optional bits to pad the frame. Ethernet frames are sized between 64 and 1518 bytes.
If the frame is smaller than 64 bytes, the sending NIC places "junk" data in the pad to
make it the required minimum of 64 bytes.
• The cyclic redundancy check (CRC) is the result of a mathematical calculation
performed on the frame. The CRC helps verify that the frame contents have arrived
uncorrupted.

Ethernet Implementations - Answer- 10BaseT
10 Mbps (half duplex)
20 Mbps (full duplex)
Twisted pair (Cat3, 4, or 5)
100 meters

10BaseFL
10 Mbps (full duplex)
Fiber optic
1,000 to 2,000 meters

Fast Ethernet - Answer- 100BaseTX
100 Mbps (half duplex)
200 Mbps (full duplex)
Twisted pair (Cat5 or higher), uses 2 pairs of wires
100 meters

100BaseFX
100 Mbps (half duplex)

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller millyphilip. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for CA$14.67. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

77764 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 14 years now

Start selling
CA$14.67
  • (0)
  Add to cart