Millwright lubrication Study guides, Class notes & Summaries

Red Seal Millwright Review Test Questions With Correct Answers Graded A+ 1. What the fire triangle? Heat, fuel, oxygen 1. What the fire triangle? Heat, fuel, oxygen PPE stands for what? Personal protective equipment Whose responsibility it for you wear Protective equipment in good order? Your own What class fire extinguisher is used for combustible metals? D What important to do before welding in tank? Check for gasses and oxygen level with an air quality tester ...

Millwright Interprovincial (Red Seal) Review Exam 3 Questions With 100% Correct Answers Graded A+ 1. How is efficiency found? A) output over input B) input over output C) output times input times 100 D) output times input divided by hp A) Output over input 2. What is the maximum capacity in kg of a heavy duty ladder? A) 136 B) 113 C) 102 D) 91 B)113 . Worn ring grooves on an engine piston will cause: A) the rings to rock back and forth. B) combustion gases to blow by the r...

1. What type of oil or grease would be used in a heavy load situation? a. Synthetic oil b. Extreme pressure lubricant c. Mineral oil d. Any hydraulic fluid b. Extreme pressure lubricant 2. The most common measurement of kinematic viscosity is what? a. Viscosity b. Centistokes c. Viscosity index d. Flash point b. Centistokes 3. When grease moves in a bearing, it tends to shear. This is known as: a. Pour point b. Viscosity index c. Directional fluidity

Millwright Interprovincial (Red Seal) Review Exam 3 Questions With 100% Correct Answers 1. How is efficiency found? A) output over input B) input over output C) output times input times 100 D) output times input divided by hp - answerA) Output over input 2. What is the maximum capacity in kg of a heavy duty ladder? A) 136 B) 113 C) 102 D) 91 - answerB)113 . Worn ring grooves on an engine piston will cause: A) the rings to rock back and forth. B) combustion gases to blow by the rin...

Millwright Test Exam Questions With Verified Answers Graded A+ 2024/2025 If the seal was not properly aligned or there is excessive wear in some bearing or shaft______ wear tracks will be the indicator. Unusual For removing hard to remove gasket materials found on sealing surfaces ______ is recommended. sharpened brass putty knife Apprenticeship training is Conducted on the job Charting alignment on a graph requires a chart that is divided into thousandths of an inch verticall...

Millwright-Preventive and Predictive Maintenance Exam Questions With Verified Answers Preventive maintenance - answeris the periodic inspection and maintenance of plant assets and equipment to uncover conditions that may to equipment failure or shortened life This measures the amount of contaminants per litre of fluid. a. ferromagnetic analysis b. total base number c. infrared tests d. gravimetric level analysis - answerd. gravimetric level analysis These tests indicate how much of the...

1. What type of oil or grease would be used in a heavy load situation? a. Synthetic oil b. Extreme pressure lubricant c. Mineral oil d. Any hydraulic fluid b. Extreme pressure lubricant 2. The most common measurement of kinematic viscosity is what? a. Viscosity b. Centistokes c. Viscosity index d. Flash point b. Centistokes 3. When grease moves in a bearing, it tends to shear. This is known as: a. Pour point b. Viscosity index c. Directional fluidityd. Shear point c. Directional flu...

1. What type of oil or grease would be used in a heavy load situation? a. Synthetic oil b. Extreme pressure lubricant c. Mineral oil d. Any hydraulic fluid - ANSWERSb. Extreme pressure lubricant 2. The most common measurement of kinematic viscosity is what? a. Viscosity b. Centistokes c. Viscosity index d. Flash point - ANSWERSb. Centistokes 3. When grease moves in a bearing, it tends to shear. This is known as: a. Pour point b. Viscosity index c. Directional fluid...

Millwright - Lubrication Math With Complete Solutions 100% 2024

NCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS & ANSWERS 100% ACCURATE. unusual - ANSWER-If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear tracks will be the indicator sharpened brass putty knife - ANSWER-For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended Conducted on the job - ANSWER-Apprenticeship training is_______ distance - ANSWER-Charting alignment on a graph requires a chart that is divided int...