NIMS test| Questions With 100% Correct Answers | Verified
81 views 0 purchase
Course
NIMS
Institution
NIMS
The safest way to remove chips from a lathe or milling machine is to use a: - brush
Small chips left out on the spindle nose of a lathe should be cleaned to avoid - Run out on work
holding devices
Grease guns are used to insert grease into: - Zerk fittings on machine tools
To lubricate the ways...
NIMS test The safest way to remove chips from a lathe or milling machine is to us e a: - ✔✔brush Small chips left out on the spindle nose of a lathe should be cleaned to avoid - ✔✔Run out on work holding devices Grease guns are used to insert grease into: - ✔✔Zerk fittings on machine tools To lubricate the ways of a lathe, the gibs of a Miller the cross slide of a grinder - ✔✔Use lubricant found in central lubricating systems ("one shots ") If a vertical mill ta ble is loose and has side play, the best solution to alleviate side play is to: - ✔✔Tighten the taper gib adjustment A machinist wants to find the proper type of lubrication, schedule and recommended maintenance practices for the headstock of a lathe. The best source to find this information is: - ✔✔Preventative maintenance schedule and machine manual General maintenance information for machine tools and machine work area can be found: - ✔✔General Maintenance Manual Pinning refers to: - ✔✔Loading the fil e with metal chips Files should be stored - ✔✔In a toolbox separated from each other The best way to clean the chips out of the file is to use - ✔✔file card What is the most common injury that may occur during a filing operation - ✔✔Being stabbed with t he tang (file without a handle) The best lubricant to prevent wear and increase cutting efficiency for tapping common steels is - ✔✔Sulfur -based oil A reaming operation produces finish tears. The cause of the tears is: - ✔✔Insufficient stock allowance What is the gage block height for an angle of 9 degrees on a 10 -inch sine plate? - ✔✔1.5643 inches Which of the following combinations of a gage blocks (from an 81 -block set) can be used to gage a length of 0.9528 inches - ✔✔0.1008, 0.102, 0.750 The proce ss of displacing air between gage blocks for accurate measurements is called - ✔✔wringing To check the height of multiple parts with gage blocks, a machinist would use a - ✔✔Dial indicator and digital height gage Surface finish is checked with: - ✔✔Comparison charts A surface finish symbol is as follows - ✔✔The surface finish is 15 micro inches What is the most common type of surface finish callout - ✔✔roughness A part is considered a reject when: - ✔✔Dimensions are out of tolerance A sampling is referred to as a: - ✔✔Samples taken from a machine over a period of time Inspection plans are needed to: - ✔✔all of the above
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller PatrickKaylian. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $7.99. You're not tied to anything after your purchase.
