Bleeder - Study guides, Class notes & Summaries

HVAC Metering Devices Exam Questions with Answers The piping between the condenser and the metering device is called? A Suction line B Discharge line C Expansion line D Liquid line - Answer-D Liquid line Which component is NOT a type of metering device? A Capillary tube B Bare tube C Automatic expansion valve D Thermostatic expansion valve - Answer-B Bare tube The diagram of an automatic expansion valve separates the atmospheric pressure and the system pressure. A True B Fals...

They type of brake fluid recommended for use in the master cylinder is ____________ DOT 3 DOT 4 DOT 4 + or LV Any of the above depending on the vehicle - Any of the above depending on the vehicle Why is a scan tool needed when checking the level of automatic transmission fluid? To determine the fluid temperature To check for any stored diagnostic trouble codes To check which solenoids inside the transmission/transaxle are active To determine the fluid capacity - To determine the fluid t...

on a car with disc/drum brakes, the front brakes grab quickly when light pedal pressure is applied. This problem could be caused by a bad.. correct answer: metering valve the drive of a vehicle with power disc/drum brakes says that the brake pedal moves slowly to the floor while maintaining pedal pressure at a spotlight. what could cause this problem? correct answer: leaking primary piston cup in master cylinder which of the following would most likely happen if the measurements taken fr...

YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? : A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHINGS WOULD BE FOUND AT: : A. POINT B. B. POINT C. C. POINT A. (CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORR...

YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? : A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHINGS WOULD BE FOUND AT: : A. POINT B. B. POINT C. C. POINT A. (CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORR...

ASE ASSOCIATE EXAM 2024 WITH 100% ACCURATE SOLUTIONS Brake Pad Minimum Thickness Customer Pay Warranty CPO - ANSWER ☑☑Customer Pay: 3mm Warranty: 4mm (3.9mm) CPO: 5 mm Brake bleed pressure setting (bar): - ANSWER ☑☑2 bar max - Location of MSDS: - ANSWER ☑☑Online CPO test drive (length and distance): - ANSWER ☑☑20 uninterrupted minutes/ 5 continuous miles Caliper bleeding with 2 bleed screws - ANSWER ☑☑Outer bleeder first, then inner - Is pres...

ASE Certification Practice Exam Both b and c - Answer ️️ -Coolant should be tested for ________. Proper color Freezing point (temperature) Specific Gravity Both b and c Both technician a and b - Answer ️️ -Two technicians are discussing a compression test. Technician A says that the engine should be cranked over with the pressure gauge installed for "4 puffs." Technician B says that the maximum difference between the highest reading cylinder and the lowest reading cylinder sho...

HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? - Correct Answer ️️ -A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHI...

1. On a car with disc/drum brakes, the front brakes grab quickly when light pedal pressure is applied. This problem could be caused by a bad: A. proportioning valve B. pressure safety switch C. metering valve D. residual check valve - correct answer -C 2. The driver of a vehicle with power disc/drum brakes says that the brake pedal moves slowly to the floor while maintaining pedal pressure at a stoplight. What could cause this problem? A. leaking primary piston cup in master cylinde...

ASE PREP TEST QUESTIONS & ANSWERS 2024/2025 Brake Pad Minimum Thickness Customer Pay Warranty CPO - ANSWERSCustomer Pay: 3mm Warranty: 4mm (3.9mm) CPO: 5 mm Brake bleed pressure setting (bar): - ANSWERS2 bar max - Location of MSDS: - ANSWERSOnline CPO test drive (length and distance): - ANSWERS20 uninterrupted minutes/ 5 continuous miles Caliper bleeding with 2 bleed screws - ANSWERSOuter bleeder first, then inner - Is prescription eye wear valid eye protection in a bmw ...