Bleeder - Study guides, Class notes & Summaries

ASE A5 Test Questions with 100% Correct Answers | Latest Version 2024 | Verified 1. On a car with disc/drum brakes, the front brakes grab quickly when light pedal pressure is applied. This problem could be caused by a bad: A. proportioning valve B. pressure safety switch C. metering valve D. residual check valve - C 2. The driver of a vehicle with power disc/drum brakes says that the brake pedal moves slowly to the floor while maintaining pedal pressure at a stoplight. What could c...

The phrase "putting the pump into gear" refers to the process of: A. priming the pump B. opening the discharge valve C. making the fire pump operational D. moving the apparatus into position correct answers C Which of the following is a recommended additional measure of safety that should be taken whenever the driver/operator leaves the cab? A. chocking the apparatus wheels B. overriding the parking brake system C. disengaging the power take off D. giving three short blasts from an ...

On a car with disc/drum brakes, the front brakes grab quickly when light pedal pressure is applied. This problem could be caused by a bad.. Correct answer metering valve The drive of a vehicle with power disc/drum brakes says that the brake pedal moves slowly to the floor while maintaining pedal pressure at a spotlight. What could cause this problem? Correct answer leaking primary piston cup in master cylinder Which of the following would most likely happen if the measurements taken from t...

HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? - Correct Answer ️️ -A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHI...

GM ASEP Manual Drivetrains Final Two technicians are discussing bleeding a hydraulic clutch. Technician A says to open the bleeder and allow the fluid to gravity bleed. Technician B says to have an assistant slowly depress the clutch pedal as the bleeder valve is opened at the slave cylinder to bleed the air out of the system. Which technician is correct? - Both technicians The engine speed increases when the driver depresses the accelerator pedal and releases the clutch pedal, but the...

The purpose of applying mechanical pressure is to remove excess resin from the components. - True Clecos are used in conjunction with --- to apply pressure to the repair. - Caul plates What type of bagging process is used on larger surfaces. - Surface Bagging The purpose of applying mechanical pressure is to hold the repair securely and prevent any shifting of the patches during the curing process. - True --- is primarily used during the vacuum bagging process to remove excess resin into...

ASE G1 Questions and Answers A tight timing belt makes what type of noise? - Answer ️️ -Whining A RWD (rear wheel drive) transmission has a leaking output shaft seal on a vehicle with 25,000 miles on the odometer. The MOST likely cause for the leakage is: - Answer ️️ -Plugged Transmission Breather filter Of the following, when replacing a CV (constant velocity) joint or boot, what is the last step before clamping the boot? - Answer ️️ -Burping Steering dampers can be used to r...

ASE Certification Practice Exam Both b and c - Answer ️️ -Coolant should be tested for ________. Proper color Freezing point (temperature) Specific Gravity Both b and c Both technician a and b - Answer ️️ -Two technicians are discussing a compression test. Technician A says that the engine should be cranked over with the pressure gauge installed for "4 puffs." Technician B says that the maximum difference between the highest reading cylinder and the lowest reading cylinder sho...

LP Gas Master Qualifier: Liquid Transfer Questions and Answers Rated A+ When bleeding gas or disconnecting filling adapters, you have gas and air present. Which is the third source of ignition you must be aware of and not let its presence? A. A Cell Phone B. Cigarette C. Static electricity D. All of the above D. All of the above The area around the point of transfer within 5 feet is called? A. Division 1 B. Flammable C. Division D. Confined area A. Division 1 How many fe...

ASE A5 Brakes Exam Questions and Correct Answers On a car with disc/drum brakes, the front brakes grab quickly when light pedal pressure is applied. This problem could be caused by a bad: A. Proportioning valve B. Pressure safety switch C. Metering valve D. Residual check valve - The correct answer is C. The metering valve delays the flow of brake fluid to the front calipers until the pressure in the system rises to a point where the wheel cylinder can overcome the tension o...