Telegraphing - Study guides, Class notes & Summaries

What document should be reviewed prior to arriving to a job site to determine if amines or polyamides will be present? - Answer - Safety Data Sheet (SDS), formerly MSDS Specification term: Will - Answer - The owner is responsible for performing the action Specification term: Should - Answer - The contractor is strongly recommended but not required to preform the action Specification term: May - Answer - The contractor has open choice on actions Specification term: Shall - Answer - The cont...

_____ are chemical compounds that have a low boiling point which are added to the asphalt mix to help keep shingles waterproof and flexible - volatiles _____ can happen when new shingles installed over old conform to the uneven shape of the underlying shingles - telegraphing _____ flashing should be installed on the lowest face of a chimney. - _____ problems are caused by shingles from different production runs with slight differences in asphalt thickness and design installed on the same r...

NACE CIP Level 1 Practical Exam Question and answers verified to passNACE CIP Level 1 Practical Exam, CIP Level 1 NACE-CIP1-001 Practice Test Questions NACE SP0188 - correct answer High and Low Voltage Holiday Testing Low-Voltage Holiday Detector - correct answer -Ground is attached directly to substrate. -Sponge saturated with a solution of tap water/wetting agent -Proper mix ratio 1oz/USgal -Proper of speed is 1ft/sec Double Stroke -Used on Coatings up to 20mils -may be used o...

NACE CIP 1 CBT 2023 Exam | Questions with Verified Answers (Newly Updated 2023) Q: When reporting the wet film thickness from a wet film thickness comb/gauge (WFT) you report? Answer: The last tooth that has coating on it. Q: Adding an incorrect solvent to a coating may cause? Answer: Non drying and non curing. Q: You are reviewing the documentation for a tank waiting project and notice there is a conflict between the project specification and the manufacture's product ...

CIP Level 1 Questions and Answers Graded A+ You are the NACE inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat, you notice small blisters in some areas of the applied lining. Your FIRST preferred course of action is to: A. Break the blisters to see what's inside B. Document the problem and advise the contractor and owner's representative C. Document the problem and advise the contractor D. Extract any liquid that m...

When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that: - Answer-Synthetic oil or grease may not be identified To achieve consistently accurate results with ALL alt test equipment - Answer-wash your hands before sampling. When holiday testing is required the Inspector is always required to enforce NACE SP 0188: - AnswerTrue If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction leve...

NACE SP0188 - Answer-High and Low Voltage Holiday Testing Low-Voltage Holiday Detector - Answer--Ground is attached directly to substrate. -Sponge saturated with a solution of tap water/wetting agent -Proper mix ratio 1oz/USgal -Proper of speed is 1ft/sec Double Stroke -Used on Coatings up to 20mils -may be used on concrete Low Voltage Holiday Detectors Common Errors - Answer--Failure to Keep probe in contact with surface -Moving the electrode too fast or slow -Over or under saturating ...

NACE SP0188 High and Low Voltage Holiday Testing Low-Voltage Holiday Detector -Ground is attached directly to substrate. -Sponge saturated with a solution of tap water/wetting agent -Proper mix ratio 1oz/USgal -Proper of speed is 1ft/sec Double Stroke -Used on Coatings up to 20mils -may be used on concrete Low Voltage Holiday Detectors Common Errors -Failure to Keep probe in contact with surface -Moving the electrode too fast or slow -Over or under saturating the sponge ...

NACE CIP 1 CBT Exam Study Guide (Quizzes and Study Questions) What inspection challenges do you expect specific to working inside containment? - illumination - control of temperature and humidity Improper atomization of the coating may cause ___ ___ ___ - uneven DFT - dry spray - overspray High viscosity due to low temperature should be corrected by ___ ___ - adding extra thinner - heating the coating SSPC Technology Guide No.12 states "Surface preparation and coating applications must have a ...

▪ Dew point is the temperature at which condensation occurs. ▪ You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining. Your FIRST preferred course of action is to: Document the problem and advise the Contractor and Owner's representative. ▪ If a contractor is using a poorly maintained compressor to supply air for abrasive blast clean...