Fillet - Study guides, Class notes & Summaries

CWB Welding Inspector Level 2 Exam Prep (Latest 2024 / 2025 Update) Questions and Verified Answers | All Modules Covered | 100% Correct | Grade A Q: In an isometric drawing, the lines (for width, length and depth) are inclined at an angle of how many degrees? Answer: 30° Q: What are the maximum number of views in an orthographic drawing? Answer: 6 Q: What are the two general classes of picture drawings? Answer: Perspective and Isometric Q: What are the 5 basic joints? Answer: 1) Butt 2) Corner ...

Boilermaker NCCR Test Questions And Answers Boilermaker NCCR Test 1 ft 3-3/4 in + 2 ft 1-1/16 in +5 ft 10- 7/8 in = - ANS 9 ft 3-11/16 in A 1-inch plate is to be cut. Why should an acetylene gerulator on a cutting rig not be adjusted over 15 PSI? - ANS Acetylene is unstable above this pressure A big control valve is pulled who is responsible for the rigging? - ANS Crane operator and rigger A boiler maker must have all of the following wh...

A weld having a triangular cross section which is applied to a T-joint, corner joint or lap joint is called a A) Butt B) T C) Fillet D) corner - Answer C) fillet A weld produced by filling an elongated hole in an overlapping member, fusing it to the member beneath is called a A) Flange weld B) spot weld C) seam weld D) slot weld - Answer D) slot weld True or False/ a fillet is a type of weld joint? - Answer False---- Butt T and Corners are weld joints A weld used to build up thin sur...

CWB Welding Inspector Level 1 Exam (Latest 2023/ 2024 Update) Questions and Verified Answers| 100% Correct| Grade A Q: From the welding problems identified below which one of the five does not fit the pattern established by the other four? a) Insufficient throat. b) Incorrect bevel angle. c) Loss of shielding gas. d) Improper fit up. e) Use of wrong consumable. Answer: a) Insufficient throat. Q: A 10 mm fillet weld has a nominal: a) Throat dimension of 10 mm. b) Area of ...

General Maintenance/ Boma Questions and Answers 100% Pass When Starting a centrifugal pump That is part of a manifold with no check valves You should open the suction valve, start the pump and open the discharge valve slowly Curb cock A Valve insert it in a water line between the corporation stop and the water meter is generally called To check sheave wear Measure each groove angle Variable pitch sheaves may be used in some cases to provide which of the following types of speec...

What is the suggested filler metal classification for welding ASTM A131 Grade DH32 steel with GMAW ? - Answer-ER70S-X When fillet welding a 3/8 inch stud in the flat position with an E7018 electrode, what diameter electrode must be used? - Answer-3/16 inch How long does welder certification last per AWS D1.1? - Answer-indefinitely, unless not engaged in the process for more than 6 months at a time With a single electrode for SAW what is the maximum size single pass fillet weld that can be ...

CSA W47.1 and CSA W59 Exam questions with 100% correct answers 2024 CSA Standard W59 covers the welding requirements for what type of steel construction? - answer-The welding requirements of CSA Standard W59 can be applied to carbon and low-alloy welded steel What types of structures are covered in CSA Standard W59? - answer-CSA Standard W59 covers statically- and cyclically-loaded (repetitive loading) structures. What is a low-hydrogen electrode? - answer-A low-hydrogen electrode...

Module 29105-15 Base Metal Preparation (19-20).fires Most work site ___________ related to welding operations are caused by cutting torches. strong The more carbon content steel has, the more ____________ the steel becomes. austenitic A term that refers to a type of metal stainless steel group, which is most often encountered by welders. chromium Common-grade stainless steels normally contain at least 11 percent _________________. classified Grain structures are the way ...

1. Localized education in an area of a bolt that is under overload conditions is referred to as? A. Sizing B. Necking Down C. Erosion D. Elongation CORRECT ANSWER b 2. The least common location for fastener failure is? A. In the head to shank fillet. B. Throughout the first thread inside the nut on threaded fasteners. C. In the mid grip. D. At the transition from the thread to the shank. CORRECT ANSWER c 3. Discontinuities that are produced during the hot or cold working of the in...

SMAW FILLET WELDS – QUESTIONS/ANSWERS

CWB Welding Inspector Level 2 Exam Prep (Latest 2023/ 2024 Update) Questions and Verified Answers| All Modules Covered| 100% Correct| Grade A Q: In an isometric drawing, the lines (for width, length and depth) are inclined at an angle of how many degrees? Answer: 30° Q: What are the maximum number of views in an orthographic drawing? Answer: 6 Q: What are the two general classes of picture drawings? Answer: Perspective and Isometric Q: What are the...