NCCER PACKAGE DEAL SOLUTIONS WITH 'A' GRADED RESULTS 2024.

NCCER Module 5 Introduction To Cooling Exam Questions 2024. The Celsius scale is based on boiling water having a temperature at sea level of_? 100° Subcooling occurs_. After all vapor has changed to liquid When the temperature of a vapor is higher than its boiling point, the vapor i...

NCCER Module 4 Complete Test Questions 2024. A tool feature added for convenience that turned out to be very unsafe and should never be used is the... Trigger Lock. Before changing the blade or bit or doing any kind of repair... Unplug the Tool! Before plugging in tools with on/off swit...

NCCER Module 4 Introduction To Power Tools Questions & Answers 2024. A Porta-Power® is an example of a __________tool. hydraulic A power miter saw combines a miter box with a _______saw. circular To prevent electrical shock, power tools should only be operated with the proper? GFCI ...

NCCER Module 4 (Power tools) Exam Questions 2024. when using power tools, never engage the? trigger lock. before replacing parts such as bits, blades or disks on any tool, you must? make sure it is disconnected from its source or energy most hammer drills will not hammer until pressure ...

NCCER module 4 - Power Tools Final Study Quiz 2024. When using a power tool, never engage the ... Trigger lock Before replacing parts such as bits, blades, or discs on any fool, you must ... Disconnect the power source Most hammer drills will not hammer until pressure is ... Applied to...

NCCER Module 3 Introduction To Hand Tools Exam Questions 2024. A chisel head should be replaced or repaired if it is shaped like a? mushroom Because of its stiffness, a folding rule is better than a cloth or steel tape for measuring ________distance. vertical In order to transfer a chal...

NCCER Module 3 (Hand Tools) Study Questions 2024. what is another name for a machinist hammer? Ball-peen hammer a heavy duty tool used to drive posts or other large stakes is called a? Sledgehammer what is the proper angle for the edge of a cold chisel? 60- degrees what types of s...

NCCER Module 2 Terms Complete Test Guide 2024. Radius 1. ........... is equal to half the diameter of a circle Acute angle 2. xxxxx_ measures between 0 and 90 degrees. Bisect 3. When you ........... an angle you divide it into two equal parts. Volume 4. ........... can be measur...

NCCER Module 1 Final Exam Study Questions 2024. What are benefits of safety Lower accident rates less turnover Arc welding safety Gas welding and burning requires the use of a filter lens of not less than No. 4 shade Safety A learned behavior and attitude Safety culture A safet...

NCCER Module 1 Questions Correctly Answered 2024. companies with strong safety cultures usually have lower? incident and accident rates what is a statement regarding safety? it's a learned behavior and attitude poor lighting, excessive noise, and inadequate guards for moving parts are ...

NCCER INSTRUMENTATION PRACTICE QUESTIONS WITH SOLUTIONS 2024. a. SCADA b. WAN c. Peer-to-peer d. Fieldbus A technology bypassing conventional I/O by using direct communications between smart field devices and associated control processors is: a. In pairs in the same enclosure b. In a mast...

NCCER HVAC Level 1, Module 8 - Soldering Brazing Exam Questions 2024. What is a neutral flame? Equal parts oxygen and acetylene What is a carburizing flame? A cooler flame used for light brazing. At what PSI does Acetylene become unstable? 15 psi What do you use to light a torch? ...

NCCER Exam 1 Correctly Answered 2024. Companies with strong safety cultures usually have lower _____. a. turnover Which of these is a true statement regarding safety? a. Safety is a learned behavior and attitude. Poor lighting, excessive noise, and inadequate guards for moving parts are...

NCCER Electrical Level 2 Module 4 Conduit Bending Practice Questions 2024. The minimum bending radius for 3" rigid conduit is _____. 13" The minimum bending radius for 1/2" rigid conduit is _____. 4" The maximum number of 90° bends allowed between pull points in a conduit system is...

NCCER Electrical level 2 module 3 Advanced Study Questions 2024. NEC requirements must be adhered to when installing incandescent recessed lighting fixtures because they are a fire hazard if installed incorrectly which of the following will shorten the life of a filament in an incandescent l...

NCCER Electrical Level 2 Module 2 Pre-Test Exam 2024. Any exposed live parts must be guarded if they are operating at 50V or more between terminals Which of the following are most likely to use dynamic braking? Forklifts In a DC series motor, how much of its full-load torque is develope...

NCCER ELECTRICAL LEVEL 1 MODULE 11- RESIDENTAL WIRING The minimum number of small appliance circuits required by the NEC® in a kitchen area is _____. ** 2 When sizing residential electrical services, the laundry load is calculated as _____. 1,500VA When sizing the general lighting load...

NCCER Electrical Level 1 Mod 4 Electrical Theory Questions Correctly Answered 2024. Which of the following is true regarding a series circuit? The current flow is the same through all resistors. Which of the following is true regarding a parallel circuit? It has more than one path for curren...

NCCER Electrical Level 1 Mod 1 Orientation To The Electrical Trade Study Guide Exam 2024. The NCCER electrical training program applies DOL standards and is a four-year program Entry into an apprenticeship program is likely to require a(n) GATB Form Test The minimum standards for the sa...

NCCER Core - Module 5 Final Exam Questions 2024. Architectural plans Drawings that show the design of the project. Also called architectural drawings. Beam A large, horizontal structural member made of concrete, steel, stone, wood, or other structural material to provide support above a larg...

NCCER Communication Skills Review Test Guide Questions 2024. In the study of communications, noise is best defined as Anything that interferes with the message being heard or understood Folding your arms in front of you makes it seem as if you are distant and unwilling to talk If someon...

NCCER Basic Safety Review Question Guide 2024. Type C Soil When you are doing excavation work, all soil must be treated as (________) soil. If you are not sure what type of soil you are working with Competent Person The (________________) on a job site must do daily inspection when excavat...

NCCER 46101 Fundamentals Of Crew Leadership Questions Correctly Answered 2024. Accountability is defined as _____. holding an employee responsible for the completing a particular duty What is a potentially important use of the daily diary that is not related to the crew leader's efficient ...

NCCER 29105 Base Metal Prep Final Exam Test 2024. Welding Code A detailed listing of rules and principals applyed to welding is Requires half the weld material Compared to a single V- groove, A double V- groove weld Slower Mechanical joint preparation is _____ than thermal joint prepa...

NCCER 26402 COMPLETE STUDY GUIDE QUESTION 2024. A No. 1 isolated conductor MUST be identified using the color .~3.5.1 gray green orange white orange Low-voltage equipment that is typically in contact with patients must be moisture-resistant and operate on . 10V or less 15V or less 20V ...

NCCER 26210-17 FINAL STUDY GUIDE TEST 2024. A current limiting circuit breaker preforms in a manner similar to conventional thermomagnetic circuit breakers at currents below a threshold of about 1000a The normal current rating of a circuit breaker is located On the handle The interrupti...

Module 29105-15 Base Metal Preparation (19-20) Questions Correctly Answered 2024. fires Most work site ___________ related to welding operations are caused by cutting torches. strong The more carbon content steel has, the more ____________ the steel becomes. austenitic A term that refe...

Module 29101-15 Welding Safety Study Guide Exam 2024. Which of these modern methods use a flux-coated consumable welding rod? A. SMAW B. GTAW C. FCAW D. GMAW A. SMAW In which of these processes is acetylene used? A. Gas tungsten arcwelding B. Carbon arc cutting C. Flux score arcwelding...

Module 26111- Wiring Commercial and Residential Questions With Answers 2024. a green screw terminal on a device is to be used for the _____ wire a. grounding a device labeled CO/ALR can be used with ______ wire b. copper , aluminum, or copper-clad aluminum the UL label on a device means...

Module 26104 - 20 COMPLETE STUDY GUIDE QUESTIONS 2024. What is the total resistance of three resistors in parallel with the values of 2Ω, 4Ω & 4Ω? 1Ω 3 MULTIPLE CHOICE OPTIONS The current flowing through a hair dryer that uses 1,200 watts of power with an applied voltage of 120V is _____...

Module 26103-20 Exam Questions With Solutions 2024. An electrical device that operates by chemically creating a potential difference between two points is a _____. battery 3 MULTIPLE CHOICE OPTIONS An electron repels a(n) ________? electron 3 MULTIPLE CHOICE OPTIONS Which of the foll...

Module 109 Intro To Material Handling Review Questions Correctly Answered 2024. Loose gloves may get caught on moving objects, and they reduce d. grip strength When lifting a load, keep the load c. close to your body The area into which a load is being lowered should be treated as a(n) ...

Module 108 Basic Employability Skills Review Questions & Answers 2024. Someone who can vouch for your skills, experience, and work habits is called a(n) d. reference One of the most important and productive methods to identify job opportunities is by a. networking with family and friends ...

Module 106 Intro To Basic Rigging Review Questions With Answers 2024. Identification tags for slings must include d. manufacturer's name or trademark The type of wire rope that is susceptible to heat damage at relatively low temperature is the a. fiber core Synthetic slings must be i...

Module 00105 QUESTIONS CORRECTLY ANSWERED 2024. Plans used for work that has to do with construction in or on the earth are called _________. Civil plans The material to e used for the walls would be found in the _______. Structural plan What information in a drawing's title block iden...

Module 104 Introduction To Power Tools Review Questions With Solutions 2024. Pneumatic tools get their power from a. air pressure The most common use of the power drill is to c. make holes in wood, metal and plastic A masonry bit is able to drill into concrete and similar material bec...

Module 0103-15 Introductions To Hand Tools Questions Correctly Answered 2024. Another name for a machinist's hammer is A. Ball-peen hammer B. Claw hammer C. Veneer hammer D. Sledgehammer A. Ball-peen hammer A heavy-duty tool used to drive posts or other large stakes is a A. Mallet B. S...

Module 00102-15 Exam Introduction To Construction Math Study Questions 2024. What is the place value of 2 in the number 123,456? Ten Thousands Forty-five thousand, six hundred twelve pipe fittings have been ordered for a large project. How would you write this number as a whole number using...

Module 00100 - Build Your Future In Construction Study Questions 2024. Craft/Trade A general term referring to one of the many construction specialties. Craft Professional A trained and skilled individual who designs and builds things. Craft professionals conform to the technical and ethical...

Module 5 NCCER TEST Construction Drawings Study Questions 2024. Plans used for work that has to do with construction in or on the earth are called Civil Plans The material used for the walls would be found in the? Structural Plans Information in a drawings title block identifies the pro...

Module 2- NCCER Introduction To Construction Math Test Correctly Answered 2024. ten thousand What is the place value of 7 in the number 576,312? 36,211 Thirty-six thousand, two hundred eleven pipe fittings have been ordered how would you write this in a whole number using digits? 1,235 ...

Level 2 Module 1 Alternating Currents Final Test Guide 2024. 2:1 What is the step-down turns ratio of a transformer with 200 turns in the primary and 100 turns in the secondary? induced high voltage Opening the secondary of a CT under load will cause a dangerous level of___. 40Hz What ...

HVAC NCCER Module 1- Intro To HVAC Study Set Exam Questions With Answers 2024. shop drawing A(n) _____ shows how a specific portion of the work is to be done. be recycled before reuse Recovered refrigerant should _____. humidifier The main elements of a mechanical refrigeration syste...

Hand Bending Study Guide Questions 2024. 90° bend A bend that changes the direction of the conduit by 90°. back-to-back bend Any bend formed by two 90° bends with a straight section of conduit between the bends. Concentric bends 90° bends made in two or more parallel runs of cond...

Core Module 3 NCCER QUESTIONS CORRECTLY ANSWERED 2024. Another name for a machinist hammer is a Ball-peen hammer A heavy-duty tool used to drive post or other large stakes is a Sledge hammer The proper angle for the edge of a cold chisel 60 degrees A Reed and Prince screw comes to...

Construction Drawings NCCER 105 Review Practice Questions 2024. Civil plans Plans used for work that has to do with construction in or on the earth are called? Structural Plan The material to be used for the walls would be found in the? Only part of an object is represented to sav...

29103-15 - Plasma Arc Cutting Test Review Study Questions 2024. Gas In PAC, plasma is created by ___________ in an electric arc? Faster & More Efficient In most cases, PAC is ___________ &___________ than other cutting methods. A full leather hood Which PPE is considered optional in PA...

29102-15 Oxyfuel Cutting Test Review. High-Pressure Pure Oxygen A stream of _______________ is directed from the torch at the metal's surface causing the metal to instantly oxidize or burn away. Ferrous metals The Oxyfuel cutting process is usually performed on _____________. 3-6 A sh...

26107-Hand Bending Final Exam Questions 2024. Which of the following should be used to cut EMT? Hacksaw A dye is used to do what? Cut threads in a pipe . Which of the following eliminates wrinkling or flattening when bending PVC Plug set . A radius of a circle is defined as what...

00104-15 (Introduction to power tools) Questions 2024. Trigger lock When using power tools, never engage the _____. Disconnect the power source Before replacing parts such as bits blades, or discs on any tool, you must______. Applied to the drill bit Most hammer drills will not hammer ...

00104 NCCER Test Baby Practice Questions 2024. Trigger lock When using power tools t=you never engage the ______________ disconnect the power source before replacing things like bits, blades, discs or any tool you must drill bit most hammer drills will not hammer unless pressure is app...