Exam (elaborations)
Mike's Ultimate Elevator Mechanics Exam Review 2024 Solved 100% Correct
- Module
- Institution
Mike's Ultimate Elevator Mechanics Exam Review 2024 Solved 100% Correct
[Show more]
Seller
Follow
LUCKYSTAR2022
Reviews received
Content preview
Mike's Ultimate Elevator Mechanics Exam Review 2024 Solved 100% Correct1. A contractor wants to raise the car speed from 100fpm to 125fpm, it currently has a 12" sheave. What sheave is required? - ANSWER-100fpm / 125fpm = 12" / X= 15"
2. A MOV (Metal Oxide Varistor) burns out. You replace it, but cannot read voltage or resistance. What should you do? - ANSWER-Replace it with a larger MOV 630
3. On a Ward-Leonard circuit the break is set, but the motor is trying to slip through the break. What is the issue? - ANSWER-Suicide Circuit 425
4. You have an old DC motor and are adding an SCR drive, what do you do to the interpoles? - ANSWER-Leave the interpoles alone. When adding a SCR drive to the generator, the series loop is removed, as are the 3 resistors. Everything else remains the same.
5. A hydro runs up with no load, but will not run with a full load. What is the issue? - ANSWER-The relief valve is set too low 815
6. Runby for a 1:1 hits the CWT buffer 4" below the top landing. CWT runby should be set at 18". How much should the ropes be shortened? - ANSWER-22" 235
7. You need to work on a freight door retiring cam, you LOTO the main line but there is still power on the cam. What circuit is still hot? - ANSWER-Door Operator Disconnect/ Main Line Disconnect 535
8. The contractor requests that the vertical center of a Rack and Pinion hoist be moved. How do you do this? - ANSWER-Adjust Tie Downs and Wall Ties 850
9. Working pressure on a Hydro is 400psi. What is the maximum relief valve setting? - ANSWER-400psi x 150%= 600psi 815
10. What must be installed on a false car before operation? - ANSWER-Spring Loaded Safeties 110
11. There is slight arcing between the brush and commutator. What action must be taken? - ANSWER-None
Note: Heavy arcing=Light brush pressure, Heavy bush pressure=mechanical wear 430
12. If rigging gear is roped 3:1 and a BEAM CLAMP is used to lift a 6,000lb load. What is the beam capacity requirement? - ANSWER-18,000lbs.
Note: Beam capacity is cut in half with use of clamp, when rigging all blocks, rope, and clamps will be Equal to the lowest load rating 210 13. How much resistance is measured over a normally closed switch? - ANSWER-
1.2ohms. should be zero, but will never be that low
14. A car traveling in the hoistway always stops at the same spot and blows a fuse. What causes this - ANSWER-Traveling cable has a cut/exposed wire or a short 515
15. How is a class 1 yearly buffer test preformed? - ANSWER-Car at bottom landing and on inspection, jump out direction and final limits.
With pit clear, run down to compress buffers, buffers should fully extend within 90 seconds.
Note: 5yr: Full load Full speed CWT: Full speed Empty 555 (may be 60 on test)
16. How many strain supports are required on a 350ft raceway? - ANSWER-4. 1 every 100ft 505-510
17) How is stainless steel drilled out? - ANSWER-Slow speed and constant pressure 205
18. What is the required amount of retainer clips for wedge shackles and what is the spacing? - ANSWER-At least 2. First clip being maximum 4 times the diameter of the rope from the top of the shackle, and the second clip is maximum 8 times the diameter of the rope above the first clip. 245
19. A 300ohm resistor burns out, but you don't have another one. How can you make one? - ANSWER-2-600ohm resistors in parallel is 300ohms. Resistance is half of highest resistor in parallel circuit. 3-225ohm resistors in parallel is 75ohms. 345
20. When cutting laminated panels, which direction should the finish side face? - ANSWER-Finish side facing the cutting edge of the tool. Blade will burr the backside 255
21. How do you cut a finished floor? - ANSWER-Cutting blade away from finished side 255
22. A 480vac stepdown 240vac transformer is connected to a 3 phase rectifier, what is the output voltage? - ANSWER-320vac 3 phase full wave = 1.33x output voltage. 715
23) Car is loaded with 125% and sinks. Why? - ANSWER-Slipping through the break
24. If you find a broken or missing barricade what should you do? - ANSWER-Write up a formal inspection request
25. What are the consequences of misaligned joints on a Rack and Pinion? - ANSWER-
Broken Gear teeth. CWT derailment. Excessive wear/ crease the surface of the tube 850 26. A dumbwaiter is 9sqft in area, 4ft high, and capacity is 13.9lb/ft3. What is total capacity? - ANSWER-9 x 4 x 13.9= 500lbs Max capacity
27. You must enter a pit with a toxic atmosphere, how do you proceed? - ANSWER-
Following proper OSHA procedure with proper training and PPE 133
28. When changing a 1:1 car rated at 600fpm and 2,000lb capacity to a 2:1, what are the new ratings? - ANSWER-300fpm 4,000lbs capacity Half the speed, Double the capacity
29. A vertical platform lift has a clearance of 1 inch. How much will it have to move to meet code? - ANSWER-Move in ¼ inch. Code is ¾ inch
30. A car weighs 2500lbs with a capacity of 2500lbs, the CWT is weighted at 40%, how much is the motor lifting when the car is fully loaded? - ANSWER-2500(car) + 1000(40%) 3500. 5000-3500=1500lbs lifted by the machine 240
31. How must Oxygen and Acetylene tanks be stored? - ANSWER-Vertically, 12 feet apart, or on a cart with a ½ hour fire barrier between them 205
32. What is code for sill to sill distance? - ANSWER-Minimum ½ inch Maximum 1 ½ inches 525
33.When drilling a jack hole in sandy conditions what type of drill rig is required? - ANSWER-Rotary or Auger bit.
Note: Rotary=Soft Percussion=Rocky Combo=Solid 810
34. A customer does not want an escape hatch on a residential elevator, under what condition is this legal? - ANSWER-Manual operation must be provided 840
35. Your helper wired the down direction and final limit switches, now the car will only travel up, what is the issue? - ANSWER-The down direction limit was wired incorrectly.
36. What are the effects of one rope sitting deeper in the sheave groove? - ANSWER-
The rope wears out and breaks faster 245
37. There is a noise coming from a freight door. The sheave is moving, but the chain is not. What is the problem? - ANSWER-Oil on the drive chain 535
38. What is the effect when you change a sling angle from 60 degrees to 30 degrees? - ANSWER-More tension, less capacity. Any angle 30 or less is dangerous 100s
39. How many points of a contact must be maintained on a ladder? How far above the landing must it extend? What steps don't we use? - ANSWER-3 points of contact. 3 foot
above. 4:1. Top 2 steps 132
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller LUCKYSTAR2022. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for £11.02. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
79223 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy revision notes and other study material for 14 years now