BOILER MAKER
when are steel chain slings recommended ? - ANS-in high heat conditions
a big control valve is pulled, who's responsible for the rigging ? - ANS-the rigger and the crane
operator
what should be used to hold the pipe when setting up two 40 foot joints of 16 inch std wt pipe? -
ANS-4 legged roller top jacks
the hitch made by wrapping the sling around the load, then passing the sling through a shackle
is called? - ANS-chocker hitch
when should rigging material be attached to a beam that is being demolished? - ANS-before
any bolts are removed or any cutting is done on the beam
which of the following has a greater possibility of being a respiratory hazard? - ANS-asbestos
which type of isolation is required before a vessel is entered? - ANS-lockout, ragout, and
blinding the lines that feed the vessel
according to OSHA oxygen and acetylene cylinders in storage must be separated at a minimum
distance of ? - ANS-20ft
what is the first thing that a boiler maker should do before cutting into a tank or vessel? -
ANS-make sure the proper permit has been obtained
what tool is normally used to check the alignment on the horizontal seams the shell plates? -
ANS-water level
what is used to expand tubes inside made and steam drums? - ANS-rolling motors and
expanders
what does grooved nut on a acetylene rig indicate? - ANS-the left tread is for acetylene use only
thermal beveling of pipe in preparation for welding requires the use of an ? - ANS-Oxyfuel torch
a 1-inch plate is to be cut, why should an acetylene generator on a cutting rig not be adjusted
over 15 psi? - ANS-acetylene is unstable above this pressure
what action should be taken if a boiler tube fails ? - ANS-replace the failed tube
before a wall burner is pulled for inspection - ANS-the fuel gas valve must be shut
, which of the following is a type of insulation used inside furnaces? - ANS-fire brick
what does "MTW" mean in reference to boiler tubing ? - ANS-Minimum wall thickness
on a drawing what is used to record any changes to the drawing? - ANS-revision block
scales on a drawing are usually written? - ANS-inches and feet
dimensional measurements can be found in all of the following except ? - ANS-mechanical flow
diagram
all vessel elevations are taken from the ? - ANS-Top of the steel on the embedded ring (base
plate)
a gate valve is being removed from a product line, all of the following procedures must be
preformed except ? - ANS-valve must be in closed position
what is a stud wrench most commonly used for? - ANS-aligning flanges
what type of valves are typically used on a sight glass to direct flow? - ANS-way valves
hand hole cap and plug material is verified by the ? - ANS-material test report
what are four major components of a gate valve? - ANS-body, bonnet, gate, and stream
what is the most commonly used fastener in boiler constructions? - ANS-threaded
on site, who determines what grade of material to be used for a repair? - ANS-QC
what is the best tool to be used to prepare XXH2-inch tubing for welding ? - ANS-milling motor
all of the following tools are used in preparation of the butt weld of a tube except? -
ANS-chipping gun
what preparations must be made for the spring can hangers of a section of a pipe before hydro
testing can be? - ANS-put the travel stops in the spring
which of the following connecting the units are used on pipe hangers? - ANS-eye bolts,
turnbuckles, threaded rods
which of the following materials maybe used to safely secure scaffold boars to platform? -
ANS-9 inch wire
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller ACTUALSTUDY. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for £6.34. You're not tied to anything after your purchase.