100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
Steering and Suspension Test 1 (CH 1,3,4,5) - Questions with 100% correct answers verified latest update 2024 £6.37   Add to cart

Exam (elaborations)

Steering and Suspension Test 1 (CH 1,3,4,5) - Questions with 100% correct answers verified latest update 2024

 5 views  0 purchase

Steering and Suspension Test 1 (CH 1,3,4,5) - Questions with 100% correct answers verified latest update 2024

Preview 2 out of 7  pages

  • June 17, 2024
  • 7
  • 2023/2024
  • Exam (elaborations)
  • Questions & answers
All documents for this subject (54)
avatar-seller
ACTUALSTUDY
Steering & Suspension Test 1
Unitized vehicle bodies (Unibodies) have these special features and applications:
A. Are typically used in large rear-wheel- drive vehicles.
B. Have special steel plates in the hood and truck lid to protect the passengers.

✅✅
C. All portions of the unibody are constantly load bearing.
D. Have a structured box like compartment to protect the passengers - -D.
Have a structured box like compartment to protect the passengers

The purpose of the upper control arm and the lower control arm in short and long
arm suspension (SLA) is to...
A. Allow the steering knuckle to turn right and left.
B. Control spring action on irregular driving surfaces.

✅✅
C. Reduce body sway.
D. Control lateral side to side wheel movement. - -D. Control lateral side to side
wheel movement.

A semi-independent rear suspension system has...
A. Rear axle with an inverted U-section containing a tubular stabilizer bar.
B. Upper and lower control arms

✅✅
C. A one-piece rear-axle housing
D. A lower ball joint - -A. Rear axle with an inverted U-section containing a
tubular stabilizer bar.

Which of the following statements about wheel rims is NOT true?
A. Wheel rims must position the tires at the proper distance inward and outward form
the vertical wheel mounting surface.
B. A wheel rim with a positive offset has the center of the tire positioned inboard from
the vertical mounting surface.
C. A wheel rim with a neutral offset has the center of the tire positioned at the center
of the brake rotor.

✅✅
D. A wheel rim with a negative offset has the center of the tire positioned outboard
from the vertical mounting surface. - -C. A wheel rim with a neutral offset has
the center of the tire positioned at the center of the brake rotor.

A thrust type bearing load is applied...
A. Horizontally
B. Vertically

✅✅
C. Tangentially
D. Radially - -A. Horizontally

Shock absorbers control spring action to help prevent...
A. Improper wheel and tire positions.
B. Wheel oscillations.

, ✅✅-B. Wheel oscillations.
C. Excessive steering effort.
D. Slow steering wheel return after a turn. -

In a parallelogram steering linkage, the tie rods are parallel to the...
A. Steering arms
B. Center link

✅✅
C. Upper control arms
D. Lower control arms - -D. Lower control arms

All of the statements about recirculating ball steering gears are true EXCEPT...
A. Ball Bearings are mounted between the steering gear and the ball nut.
B. The Lower end of the selector shaft is splined to the idler arm.
C. As the steering wheel is turned, the ball nut moves upward and downward on the

✅✅
worm gear.
D. The steering shaft is attached to the worm gear. - -B. The Lower end of the
selector shaft is splined to the idler arm.

Excessive rear wheel toe-out on the left rear wheel causes...
A. Excessive tire tread wear
B. Harsh ride quality

✅✅
C. Reduced steering effort
D. Excessive wheel oscillations - -A. Excessive tire tread wear

Proper wheel alignment is extremely important to provide all of the following
EXCEPT...
A. Steering control
B. Ride quality

✅✅
C. Minimizing suspension vibration
D. Normal tread life - -C. Minimizing suspension vibration

All of the following statements are true EXCEPT...
A. Zero offset, the rim center line aligns with the mounting surface of the rim.
B. Positive offset, the rim center line is inboard of the mounting surface of the rim.
C. Positive offset, the rim center line is outboard of the mounting surface of the rim.

✅✅
D. Negative offset, the rim center line is outboard of the mounting surface of the rim.
- -C. Positive offset, the rim center line is outboard of the mounting surface of
the rim.

When did TPMS systems become federally mandated?
A. 1996
B. 2006

✅✅
C. 2000
D. 2008 - -D. 2008

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller ACTUALSTUDY. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for £6.37. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

79271 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy revision notes and other study material for 14 years now

Start selling
£6.37
  • (0)
  Add to cart