Exam (elaborations)
Plumbing level 1.
- Module
- Nccer Plumbing
- Institution
- Nccer Plumbing
Exam of 13 pages for the course Nccer Plumbing at Nccer Plumbing (Plumbing level 1.)
[Show more]
Seller
Follow
Content preview
Plumbing level 1The pipe from the water main, water meter, water supply system or other approved
source of water supply,to the building or structure - ANS-Water service pipe
Any pipe or fitting which makes angle of more than 45° with the vertical -
ANS-Horizontal pipe
The length of a pipe along the centerline of the pipe and fittings - ANS-Developed length
For applicability requirements of the plumbing code, refer to: - ANS-The plumbing code
102.1
The provisions of the plumbing shall apply to: - ANS-Installations, alterations and
repairs, replacements - 101.2
The provisions of the plumbing code shall NOT apply to... - ANS-Gas fired water heater,
water heater venting systems, fuel gas piping
What is the minimum size of a building sewer? - ANS-4 inches T710.1 (1) b
Minimum fall shall not be less than _____ per foot for a 2 inch pipe or _________ per
foot for a 4 inch pipe. - ANS-1/4":1/8". T704.1
A pipe or a fitting which makes an angle of not more than 45° with the vertical is
considered - ANS-Vertical pipe. 202- definitions
Cleanouts in 4 inch building sewer shall not be located more than ____ft. apart -
ANS-100 ft. 708.3 .2
Size of cleanouts for a 4 inch pipe or larger may be served by a _______inch clean out -
ANS-4". 708.7
Size of cleanouts for less than a 4 inch pipe ---- 4 inch, 2 inch, size of pipe or 3 inch? -
ANS-Size of pipe 708.7
Waste and soil pipe leaving a building shall have an earth cover ______ inches - ANS-3
inches. 305.6.1
, A manhole cover in a flood hazard zone (a zone) shall be sealed unless - ANS-The
manhole is elevated above base flood elevation 309.2#6
Temporary toilet facilities need not be on site for crews on a job site for no more then
which of the following? - ANS-One day 311.1
Strainer plates on drain inlet shall be designed with openings not greater than ____ -
ANS-.5 " 304.2
What is the size of a sleeve passing through a wall to protect piping? - ANS-Two pipe
diameters greater than the pipe 305.5
All plastic pipe, fittings and component shall be third-party certified as conforming to
which of the following? - ANS-NSF 14. 303.3
All openings around pipes, tubing, wiring, conduit, Etc. Shall be fire stopped according
to which of the following? - ANS-The building code 307.3
The top of water pipes, installed below grade outside the building, shall be: -
ANS-Below the frost line or minimum of 12 inches below finished grade which ever is
greater 305.6
Water piping installed in an unconditioned area shall be insulated with a minimum R
factor of: - ANS-6.50 305.6
Trenches installed parallel to footings shall not extend below the bearing the plane of
the footing: - ANS-45° 307.5
Exterior wall openings shall be made which of the following? - ANS-Watertight. 305.7
Notches at the end of joists shall not exceed: - ANS-1/4 of the depth. 307.2, F101.1
The edge of a bored hole in a stud shall be no closer to the edge than: - ANS-5/8"
307.2, F101.3
Protective shield plates shall extend at least which of the following above the sole plate
- ANS-2" 305.8
When backfilling above a pipe is complete, which of the following is the proper depth
above the crown of the pipe? - ANS-12" 306.3
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller denicetho. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for £7.16. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
75632 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy revision notes and other study material for 14 years now