Exam (elaborations)
MSSC Quality 4.0 Questions and and answers
- Module
- MSSC Quality Systems
- Institution
- MSSC Quality Systems
MSSC Quality 4.0 Questions and and answers
[Show more]
Content preview
MSSC Quality 4.0Question: __________ include the standards and specifications for conformance and results
of the inspection. - correct answer-Inspection Documentation Forms
Question: __________ should be destroyed after specified time limits. - correct
answer-Stored data reports
Question: __________ should be validated and approved to ensure accuracy. - correct
answer-Standard operating procedures
Question: __________ should be validated and approved to ensure accuracy. - correct
answer-Standard operating procedures
Question: __________ welds are used to connect two plates using holes in one or both
plates to allow access for the welding tool. - correct answer-Plug and slot
Question: 0.001 is __________. - correct answer-One thousandth
Question: 10 inches is the same length as __________ mm. - correct answer-254
Question: 5S is a lean manufacturing technique that focuses on creating a(n) __________. -
correct answer-Clean and orderly work area
Question: 67,500 millimeters is equal to how many kilometers? - correct answer-0.0675 km
Question: 76.2 mm is equal to __________ inches. - correct answer-3.0
Question: A __________ examines all the elements in a QMS to determine how appropriate
and effective the entire system is as a whole. - correct answer-Quality system audit
Question: A __________ is an important measuring tool in manufacturing because it can
easily be carried in a pocket and provides quick measurements and approximate
dimensions. - correct answer-Machinist's rule
Question: A __________ provides a very accurate finished base on which to measure parts.
- correct answer-Surface plate
Question: A bell-shaped curve can be described by which of the following statements? -
correct answer-Plotted data values that show good central tendency
Question: A Corrective Action Report was submitted to prevent using the wrong foam in a
packaging process. This has been a recurring problem. The normal audit time in this
department is usually every six months. What should be done in this situation? - correct
answer-The foam should be checked every time it is replenished and documented
,Question: A device that is always used as a reference surface is a __________. - correct
answer-Surface plate
Question: A flat plane that is perpendicular to the direction of a measurement is a
__________. - correct answer-Reference plane
Question: A frequency chart is typically used to establish __________. - correct
answer-Sampling plans
Question: A history of dependability and customer satisfaction should be considered when
__________. - correct answer-Evaluating a potential supplier
Question: A hold tag should always be put on a calibrated tools shipment if __________. -
correct answer-It arrives with no certifications
Question: A metric micrometer showing 16.256 mm equals __________. - correct
answer-0.640 inches
Question: A micrometer measures length to an accuracy of __________. - correct
answer-0.0001 inch
Question: A part measuring 44.85 mm in a process with a tolerance of 45mm +/- .28 is
considered __________. - correct answer-In spec (within the tolerance range)
Question: A process drawing __________. - correct answer-Is required for each major step
of the manufacturing process
Question: A production line has been stopped due to a quality-related issue. After a quality
audit is performed and it has been shown that parts can be made within specifications, what
happens next? - correct answer-Production can begin
Question: A special cause variation will not create a bell curve in the data. What is said of
the process if the variation is special? - correct answer-Unstable
Question: A third-party __________ is independent and external to the organization being
audited. - correct answer-Audit organization
Question: A universal standard makes it possible for engineering drawings __________. -
correct answer-To be used in many different countries
Question: A weld's contour is the shape of the weld's surface and can be everything below,
EXCEPT __________. - correct answer-Round
Question: A worker should __________ any time the worker notices a minor quality problem
that is not critical to product function or performance. - correct answer-Notify the supervisor
to determine the correct action to take
, Question: A worker should always ask for help if __________. - correct answer-He/she does
not understand what is expected for a step of a process
Question: Accepted parts have been inspected and are __________ with specifications. -
correct answer-In conformance
Question: After a quality audit, the audit follow-up report is prepared to address __________
upon returning at a later date. - correct answer-Completed corrective actions taken
Question: All employees in the plant benefit when __________. - correct answer-Defect
trend data is collected and problems are corrected
Question: All knowledgeable persons should be encouraged to recommend __________. -
correct answer-Corrective actions
Question: Although surface plates can be made from other materials, __________ is the
most popular due to its physical properties. - correct answer-Granite
Question: An accurate problem statement, the root cause, and an effective solution are the
most important elements in a __________. - correct answer-Corrective Action Report (CAR)
Question: An auditor must perform the follow up and closure of an audit by verifying
__________. - correct answer-Corrective actions were taken and are effective
Question: An employee should report to their supervisor if the following situation occurs: -
correct answer-There is an increase in the number of defective parts produced by a
machine.
Question: Auditors should always __________ if the (a) problem has been corrected. -
correct answer-Include the problem in their report
Question: Basic and exploded view are two types of __________ drawings. - correct
answer-Assembly
Question: Before calibrating any measurement tool, including scales, make sure the tools,
weights, gauge blocks, etc., are __________. - correct answer-Clean and undamaged
Question: Before using a tool for a critical measurement, the tool may be required to be
__________. - correct answer-Calibrated
Question: Calibration means to __________. - correct answer-Adjust a device to a standard
Question: Calibration of measuring instruments is important because it ensures that the
instrument is __________. - correct answer-Accurate
Question: Calipers measure length to an accuracy of __________. - correct answer-0.001
inches
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Hkane. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for £6.31. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
83637 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy revision notes and other study material for 14 years now