If two 10-ohm resistors are connected in series, what is the total resistance of these resistors? - ANSWER20 ohms
In a split-phase motor, how much greater is the starting current when compared to the full-load current? - ANSWER6 to 8 times
The terminals of a motor can be identified using a batter...
If two 10-ohm resistors are connected in series, what is the total resistance of these resistors? -
ANSWER20 ohms
In a split-phase motor, how much greater is the starting current when compared to the full-load
current? - ANSWER6 to 8 times
The terminals of a motor can be identified using a battery and a ___ - ANSWERvoltmeter
A 5-ohm and a 20-ohm resistor are connected in parallel. What is the total resistance of these two
resistors? - ANSWER4 ohms
The normal location to provide overcurrent protection in an electrical circuit is ___ - ANSWERwhere
the conductor receives its supply
Which factor determines the outcome of an electrical shock? - ANSWERThe amount of current
Isolated power systems are used to prevent ___ - ANSWERpower interruption
The speed of a three-phase squirrel cage induction motor is controlled by the frequency of the
applied voltage and ___ - ANSWERthe number of poles
Where insulating protective equipment may be damaged, it ___ - ANSWERrequires its own
protection (e.g., leather gauntlets over rubber gloves)
Individual branch circuits are not required for portable X-ray equipment requiring no more than ___ -
ANSWER60A
The type of rubber protective equipment that is made of natural rubber or a vulcanized synthetic is
___ - ANSWERType 1
Line isolation monitors must have a green signal lamp that glows when the system is isolated from
ground and located ____ - ANSWERso it is visible to staff in the anesthetizing location
Under strict safety guidelines, which of the following should be used to discharge capacitors before
working on de-energized circuits? - ANSWERA safety shorting probe
Which of the following motors is the best installation choice for an application requiring adjustable
speeds? - ANSWERShunt DC
To make sure the voltage is turned off before touching any terminals, use a ___ - ANSWERvoltage
tester
If you bend from the waist to pick up an object weighing 20 pounds, the amount of pressure applied
to your lower back is ___ - ANSWER200 pounds
In addition to the NEC, the emergency electrical power for hospitals is governed by the ___ -
ANSWERJoint Commission
,OSHA CFR 1910 is the standard for ______. - ANSWERgeneral industry
The most common conductors used for light and power installations range from ___ - ANSWER4/0 to
No. 14 AWG
A circuit has a source voltage of 50V and a current of 10A. What is the power in watts? - ANSWER500
What is the total resistance of a two-wire circuit that spans a distance of 200' each way if the
resistance per 1,000' is 1.21 ohms? - ANSWER0.484 ohm
The primary method of varying the speed on a DC shunt motor is to adjust the voltage and current
on the field winding or the ___ - ANSWERarmature
The normal beating heart can be upset by an electrical current as small as ___ - ANSWER75mA
A three-phase induction motor may have ___ - ANSWER2 poles
Which of the following motors provides constant speed from no-load conditions to full-load
conditions? - ANSWERSynchronous
If a circuit has 12 amps of current and the resistance is 20 ohms, the applied voltage is ___ -
ANSWER240 volts
The power factor of an induction motor at no-load conditions can be as low as ___ - ANSWER15%
To keep the voltage drop of a 277V circuit to a maximum of 3%, what would be the maximum
allowable voltage drop? - ANSWER8.3V
Which of the following must be considered when determining the size of the conductor required to
connect an electrical load to the source of supply? - ANSWERPermissible voltage drop
DC injection breaking is used on the ___ - ANSWERthe stationary windings of AC motors
According to NEMA definitions, which of the following is a type of open motor? - ANSWERWeather-
protected
A polyphase synchronous motor has three stator windings that are ___ - ANSWER120 degrees apart
The value indicated in rpm on the nameplate is the ___ - ANSWERrated full-load speed
In a medical facility, receptacles should be mounted ___ - ANSWER24" above the floor
Horsepower is used to rate the ___ - ANSWERoutput capacity of a motor
If a circuit has 48 amps of current and an applied voltage of 240 volts, the resistance is ___ -
ANSWER5 ohms
The NEC requires motor disconnecting means be ___ - ANSWERwithin sight of the controller location
What is the applied voltage if the current in a circuit is 60 amps and the resistance is 10 ohms? -
ANSWER600 volts
Which of the following substances is considered a good semiconductor? - ANSWERSilicon
If the resistance of a circuit is 25 ohms and the current is 10 amps, the power in watts is ___ -
ANSWER2,500
,Which of the following is used to step voltage down to lower levels before it reaches a home or
office? - ANSWERTransformer
The stationary magnet of a DC motor is represented by the ___ - ANSWERfield poles
For a constant-torque load, the horsepower increases and decreases ___ - ANSWERin direct
proportion to the speed
Any exposed live parts must be guarded if they are operating at ___ - ANSWER50V or more between
terminals
Which of the following motors is used when the required starting torque is high and speed control is
desirable? - ANSWERCompound
A correction factor must be applied if the ambient temperature is above ___ - ANSWER86 degrees
Fahrenheit
Health care facilities are often supplied by two or more distribution points; this is known as a ____ -
ANSWERspot network
What must happen before any work may be performed in a confined space? - ANSWERCompletion of
a hazard review
A delta-connected motor has ___ - ANSWER9 leads
The synchronous speed at which a four-pole, 60Hz induction motor operates is ___ - ANSWER1,800
rpm
According to NEMA definitions, which of the following is a type of totally enclosed motor? -
ANSWERwater-cooled
If a conductor has a diameter of 40 mils, what is the diameter in inches? - ANSWER0.04"
A typical constant-torque load would be a ___ - ANSWERconveyor
Attachment plugs and receptacles in hazardous locations must be listed for use in ____ -
ANSWERClass I, Group C locations
Which of the following should have side rails that extend 36 inches above the top support point? -
ANSWERStraight ladders
How many amps are there in the current of a circuit if the voltage source is 140V and the resistance
is 2 ohms? - ANSWER70 amps
Installation of X-ray equipment is governed by ____ - ANSWERNEC Article 517, Part V
Which of the following is most likely to use dynamic braking? - ANSWERForklift
If five No. 10 AWG current-carrying conductors are installed in a raceway where the ambient
temperature is 70 degrees Fahrenheit, the allowable ampacity must be ___ - ANSWERreduced by
80% of its value
The square mil area of a conductor that is 0.250" on all sides is ____ - ANSWER62,500 square mils
, You are required to be evaluated by a physician to ensure that you are physically fit to use which of
the following types of protective equipment? - ANSWERRespirator
Low voltage equipment that is typically in contact with patients must be moisture-resistant and
operate on ___ - ANSWER10V or less
Which of the following is true with regard to working near cranes? - ANSWEROnly individuals trained
in rigging should ever rig material for a lift.
Which of the following battery byproducts can be explosive when mixed with air? -
ANSWERHydrogen
Operating rooms must be provided with a minimum of ___ - ANSWER36 receptacles
Insulating gloves must be inspected by the user ______. - ANSWERbefore each use
Which motor should be used for applications that require frequent starts without overheating the
motor? - ANSWERWound rotor induction motor
In a parallel circuit, the voltage drop ___ - ANSWERis the same across all loads
When a guardrail cannot be attached to a building, a solution may be to install a ______. -
ANSWERcontrolled access zone
Which of the following supplies power to the areas that are directly related to patient care, including
emergency rooms and pharmacies? - ANSWERCritical branch
For safety, assume that any facility constructed before 1980 contains ______. - ANSWERasbestos
The OSHA lockout/tagout rule protects workers from ___ - ANSWERexposure to hazardous energy
sources
The physical properties of a No. 4/0 copper conductor would be found in ___ - ANSWERNEC Chapter
9, Table 8
Materials with electrical characteristics that fall between those of insulators and conductors are
considered ____ - ANSWERsemiconductors
How much of a correction factor is needed if the ambient temperature is 40 degrees Celsius? -
ANSWER0.82
A medium-size motor has a frame number of 284T. The D dimension of this motor is ___ - ANSWER7"
If the wooden handle on a tool is cracked, ___ - ANSWERtag the tool out of service and do not use it
Which of the following statements is true about Type MC cable in patient care spaces? -
ANSWERType MC cable with a health care facility rating must be used.
Correction factors for reductions due to high ambient temperatures are found in ___ - ANSWERNEC
Table 310.15(B)(2)(a) and (b)
Voltage is defined as the ___ - ANSWERforce that causes electrons to flow
The capacitor-start motor is the single-phase motor type that has the ____ - ANSWERhighest starting
torque
A No. 1 isolated conductor must be identified using which of the following colors? - ANSWEROrange
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller papersmaster01. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for £13.05. You're not tied to anything after your purchase.
